| | | |Chem201L | | Determination of an Unknown Compound using Mixed Melting Point Method Winnie Adrian Ibanez‚ Jerome Allan Japitana‚ and Dante Jimenez III Group no. 7‚ 2Chem a Department of Chemistry‚ College of Science‚ University of Santo Tomas‚ España‚ Manila‚ 1015‚ Philippines |ARTICLE INFO
Premium Chemical compound Chemistry Melting point
expected‚ I found that it boiling point was 60C but in my experiment it was 30 C it’s the double of what it should be. Most of the sample like methanol and ethanol was pretty clos to the result that I found on internet. The trial that I did was Butanol again with the hot plates and it took of course much longer to boil and it started to boil before 105 °C like at 103 °C and I didn’t expect that happen maybe because of the boiling water it accelerated the boiling point. I don’t consider my
Premium Water Alcohol Boiling
Crystallization and Melting Points Organic Chemistry 221 9/19/2012 Intro/Purpose: The purpose of this lab was to use crystallization to separate a compound from a solvent and be able to choose the best solvent to do so. Then identify an unknown and verify purity using melting points. Solubility contributes to crystallization; because a solute has lower solubility at lower temperatures‚ which makes the solvent separate from the solution as a solid. This process is important to understand because
Premium Solubility Chemical polarity
Recrystallization and Melting Point of Benzoic Acid Organic Chemistry 1 10/4/12 Abstract Recrystallization was done to remove impurities from the sample. The percent recovery of benzoic acid during recrystallization is 23.02%. The difference between the pure and impure samples was observed by comparison of melting points. It was found that impure sample had a lower and wider melting point range of 120.1-122.2 (C). The pure sample melting point range was 121.3-122.5 (C). These ranges helped determine
Premium Solubility
Organic chemistry 201 | Mixed Melting Points | Determination of an Unknown Solid | | [Type the author name] | 9/15/2011 | Purpose : The main purpose of this experiment was to identify an unknown compound/substance by performing multiple experimental melting point tests. Pure and impure solids were tested to see what affect pureness/impureness had on a melting point. Background: The melting point of a solid can be used to determine the purity of the solid. Pure samples usually have
Premium Atom Chemistry Oxygen
Melting Point Determination and Thermometer Calibration Lab Background: The melting point of a substance‚ a solid in this case‚ signifies the temperature at which the first crystal starts to melt until the temperature at which the last crystal disappears is reached. That being said‚ melting points are expressed in ranges‚ am organic compound will have a sharp range depending on the purity of the compound. Impurity of an organic substance will register an abnormal melting point based on its
Premium Salicylic acid Temperature Chemical compound
Lab #1: Melting Points of Organic Compounds Report Form May 15‚ 2014 1. A “Melting Point Range” refers to the range of temperature at which a solid melts into its liquid state. 2. Pure compounds have narrow or ‘sharp’ melting point ranges‚ 1°C or less if the compound is very pure. A less pure compound exhibits a broader melting point range‚ between 3°C to 10°C as well as a depressed or lower range. 3. Crushing the sample allows for greater surface area-to-volume ratio of the powder‚ this
Premium Temperature Thermodynamics Heat
Spectroscopy‚ Boiling point and Melting point. Introduction: - Infrared spectroscopy has also made a break though in medicine. It used to evaluate the kidney stone diseases thus broadening the use of IR in different ways. The purpose of this lab experiment is to identify the unknown solutions using the Infrared Spectroscopy (IR)‚ boiling point‚ and melting point (1). The IR helps to determine the compounds such as a functional group. In order to analyze the compound‚ IR and melting point work the best
Premium Bacteria Chemistry Temperature
5. Calculated mass of the sinker in ounces 1.74g Part C 1. Length of the foil 8.5cm 2. Width of the foil 8.5cm 3. Mass of the foil .60g 4. Volume of the foil .222 5. Thickness of the foil .0031 Part D 1. Boiling point of the ethanol 65ºc Part E 1. T¹ initial temperature 125ºc 2. T² final temperature 155ºc Post lab questions: 1. Based on my temperature value and my lab measurements‚ I calculated that the water density would be 2.16 (g/mL). This
Premium Density Kilogram Measurement
Melting Points Elizabeth McGrail Organic Chemistry I 25 January 2013 ABSTRACT The objectives of this lab are‚ as follows; to understand what occurs at the molecular level when a substance melts; to understand the primary purpose of melting point data; to demonstrate the technique for obtaining the melting point of an organic substance; and to explain the effect of impurities on the melting point of a substance. Through the experimentation of three substances‚ tetracosane‚ 1-tetradecanol and
Premium Chemistry Molecule Temperature