5. Calculated mass of the sinker in ounces 1.74g Part C 1. Length of the foil 8.5cm 2. Width of the foil 8.5cm 3. Mass of the foil .60g 4. Volume of the foil .222 5. Thickness of the foil .0031 Part D 1. Boiling point of the ethanol 65ºc Part E 1. T¹ initial temperature 125ºc 2. T² final temperature 155ºc Post lab questions: 1. Based on my temperature value and my lab measurements‚ I calculated that the water density would be 2.16 (g/mL). This
Premium Density Kilogram Measurement
Determine the melting points of two organic compounds known to have the same melting range when pure. b) Determine the mixture melting point of a mixture of the two pure compounds. c) Identify an unknown organic compound by determining its melting point and mixture melting point. Procedure and Observations: Using the procedure outlined in Appendix A of the Lab Manual‚ approximately equal samples of p-Nitrophenol and acetanilide‚ which are known to have the same melting range of 113-114
Premium Chemical compound Chemical substance Temperature
BOILING POINT G1 Decreases going down. Because metal bonds get weaker. Less energy is required this metallic bonding. BOILING POINT G 17‚18 Increases. Because the atomic size incrases. The molecules are attracted by intermolecular forces. Going down the group‚ the intermolecular forces increases. More energy is needed to overcome these stronger forces. DENSITY Because mass increases faster than volume. REACTIVITY OF GROUP 1 The number of occupied shells increases. The atomic size increases
Free Atom Electron
Results My unknown sample was number 18. I did three melting point trials‚ which resulted in a melting point range of approximately 120°C to 122°C‚ as shown in Table 1. I also did two mixed melting point trials using Benzoic Acid and Succinimide‚ as shown in Table 2. Percent recovery is 28.26 grams. Table 1: Unknown Melting Point Trials Trial Melting Point 1 120°C – 122°C 2 120°C – 122°C 3 119°C - 122°C Table 2: Mixed Melting Point Trials Trial Benzoic Acid MP Unknown #18 MP Succinimide
Free Chemistry Chemical substance Benzene
Solids: Recrystallization and Melting Points Reference: Chapter 3. Solids: Recrystallization and Melting Points. Read pages 93-94 and 113-117. Experimental procedure‚ pages 118-119. Parts 1-3. Part 1: Melting points of Urea and Cinnamic Acid. Part 2: Melting point of unknown. Part 3: Melting point of Mixture- Urea and Cinnamic Acid (take melting points of mixtures in 1:4‚ 1:1 and 4:1 ratios). Reactions Main Reaction: Not a chemical reaction but a physical reaction. Urea in solid mixed with
Premium Chemical substance Temperature Mixture
DETERMINATION OF BOILING POINTS Introduction: The boiling point of a compound is the temperature at which it changes from a liquid to a gas. This is a physical property often used to identify substances or to check the purity of the compound. It is difficult‚ though‚ to find a boiling point. Usually‚ chemists can only obtain a boiling range of a 2 - 3oC accuracy. This is usually sufficient for most uses of the boiling point. Purpose: The purpose of this experiment is to determine the boiling points
Free Gas Temperature Water
ABSTRACT Determining the melting point of a solid organic compound is the easiest way to identify the compound and determine its purity at the same time. For actual samples of compounds‚ the melting will occur over a range of temperatures making the melting points into a melting “range”. The difference between the temperature at which the sample begins to melt and the temperature at which it finishes melting‚ or the magnitude of the melting range‚ is a very important criteria of determining the
Premium Freezing-point depression Melting point Temperature
with an acetic anhydride. Color impurities present in the solid acetaminophen will be removed and then the decolorized product will be collected on a Büchner funnel for further purification by crystallization. Purity will then be determined by melting point. Introduction: Acetaminophen is commonly used as an analgesic to reduce pain and fever. In this experiment it is prepared by the reaction of p-aminophenol with acetic anhydride‚ as illustrated below. Results: Isolation of crude acetaminophen The
Premium Melting point Yield Acetic anhydride
ago. My wide spread use over the course of human existence is the very reason that no one knows who discovered me. I belong to the group of elements called the transition metal group. I have several oxidation states and I also have a very high melting point which is around 1337.33 Kelvin. That is very high‚ in Fahrenheit it is 1947.92 degrees and in Celsius it is 1064.18 degrees. I am also paramagnetic‚ which means that I have very weak attractions to magnetic forces and can only be attracted when
Premium Gold
VI: Conclusion: The melting point of a compound is the temperature at which the solid is in equilibrium with its liquid. A solid compound changes to a liquid when the molecules acquire enough energy to overcome intermolecular forces holding them together in an crystalline lattice structure. The melting point range is defined as the span of temperature from the point at which the crystals first begin to liquefy to the point at which the entire sample is liquid. This data can be tabulated experimentally
Free Solid Liquid Temperature