LECTERUR : EXPERIMENT 4 DETERMINING MOLECULE WEIGHT BY FREEZING POINT DEPRESSION METHOD STUDENT NAME : ID : LAB PARTNERS | | INTRODUCTION According to Anne‚ n.d‚ the freezing point of a liquid is decreased by adding to another compound to it. This is known as freezing point depression. The pure solvent will have higher freezing point than the solution. Colligative property of matter can explain more about freezing point depression. Whereas‚ colligative properties depends on the number
Premium Freezing-point depression Melting point
Nick Boyea Billy Lee 3/9/11 Molar Mass by Freezing Point Depression Overview The purpose of this lab is to measure the freezing point depression of a solution of an unknown substance and BHT to determine the molar mass of the unknown substance. Summary of Lab Procedure If not already completed‚ crush a small amount of BHT and pack it into a capillary tube. Use a small rubber band to clamp the capillary tube to the thermometer‚ and fasten the thermometer to a ring stand. Fill a Thiele tube
Premium Melting point Freezing-point depression Liquid
Lab Name: Molar Mass by Freezing Point Depression Researcher: Isabella Cuenco Lab Start Date: November 9‚ 2012 Lab Completion Date: November 9‚ 2012 Table of Contents SECTION NAME I. Introduction II. Procedure III. Data IV. Analysis V. Conclusion PAGE NUMBER I. INTRODUCTION Purpose: The purpose of the lab is to find the molar mass of an unknown substance by measuring the freezing point depression of a solution of the unknown
Premium Melting point Freezing-point depression Liquid
PREPARATION OF ASPIRIN AND DETERMINATION OF THE MELTING POINT Ferrer‚ Lara Melissa V. Faculty of Engineering University of Santo Tomas Manila‚ Philippines ABSTRACT This experiment involved three steps: synthesis of aspirin‚ isolation and purification‚ and the estimation of purity of the final product. The synthesis involved the reaction of salicylic acid and acetic anhydride in the presence of a catalyst‚ phosphoric acid‚ H3PO4. When the aspirin was prepared‚ it was isolated and filtered. The percentage
Premium Aspirin Acetic acid Acetic anhydride
Experiment 3 Colligative Properties Freezing-Point Depression and Molar Mass By‚ Andrew Klingsporn Joby J. Chem 212 Dr. Chandana Meegoda 2/11/2009 Purpose The purpose of this experiment is to determine the Molar Mass of an unknown substance using its freezing point depression. Introduction There are two types of mixtures; homogenous and heterogeneous. Homogenous mixtures have components that are uniformly mixed‚ while heterogeneous mixtures do not. A solution is a homogenous mixture
Premium Freezing-point depression Melting point Mixture
Molar Mass by Freezing Point Depression November 28‚ 2012 NAME Lab partner- Purpose: To determine the molar mass of an unknown substance by measuring the freezing point depression of a solution of an unknown substance and BHT. Equipment: Test tube‚ 18*150 millimeters Wire stirrer Weighing dish Timer‚ seconds Chemicals: 2‚ 6-Di-tert-butyl-4-methylphenol‚ BHT‚ 16 grams Cetyl alcohol‚ CH3(CH2)14CH2OH‚ 1 gram Unknown substance
Premium Mass Melting point Measurement
Purpose: The purpose of this lab was to determine the freezing point of pure water‚ the experimental van’t Hoff factor for a substance and the molar mass of an unknown solution. Reagents: 25mL deionized Water ¼ to ½ inches of rock salt 25mL Sodium Nitrate (NaNO3 ) 25mL unknown solution – handle unknown solution carefully Procedure: For part 1‚ the freezing point of deionized water was determined. An ice bath was prepared by filling a 600mL beaker ¾ full of ice and covered with ¼ to
Premium Concentration Chemistry Water
Introduction The purpose of the experiment was to determine the melting points of compounds using a Mel-Temp device. The melting point of naphthalene‚ urea‚ and sulfanilamide are found. This is then followed by the measuring of an unknown compound‚ and an impure sample (a small amount of naphthalene mixed with the unknown). Experiment In the lab‚ the height of the chemical in the capillary was set to 2-3 mm thickness. The voltage at the Mel-Temp started at a low setting of 1.5-2. The heat was
Premium Temperature
Lab/ Chem 234 02/17/13 Lab 2: Melting Points Purpose: To determine the purity of a substance using melting point as physical property. We must also learn how to identify an unknown compound using its melting point. We got to identify an unknown compound using mixture melting point and finally we must learn to obtain an accurate melting point using Mel-Temp apparatus. Procedure: Set voltage to obtain the desired heating rate at the anticipated melting point range. The voltage control controls
Premium Temperature Fahrenheit Celsius
Organic chemistry 201 | Mixed Melting Points | Determination of an Unknown Solid | | [Type the author name] | 9/15/2011 | Purpose : The main purpose of this experiment was to identify an unknown compound/substance by performing multiple experimental melting point tests. Pure and impure solids were tested to see what affect pureness/impureness had on a melting point. Background: The melting point of a solid can be used to determine the purity of the solid. Pure samples usually have
Premium Atom Chemistry Oxygen