Sample Lab Report for CHM 152 Name Lab Partner(s) Abstract: The physical properties‚ including the boiling point‚ density‚ and refractive index were measured for unknown liquid #16. The infrared (IR) spectrum of the compound was also taken. Based on the data collected‚ it was determined that the compound was likely to be salicylaldehyde. Introduction The purpose of this experiment was to determine the identity of an unknown organic liquid by measuring some of its physical
Premium Temperature Liquid Fundamental physics concepts
Ideally‚ the percent yield should be 100%‚ as this means that you have recovered 100% of that material. A yield over 100% would mean that the substance still has some traces of another material that is adding additional mass. Ex. The iron filings having some sand particles leftover. A yield under 100% would mean that some of the substance was not recovered‚ it could have been lost (spilled) or found in another substance (not separated completely). The percent yields may give some insight into what
Premium The Final Melting point Carbon
The earth has not always looked the way it looks today. In other words‚ the United States one billion years ago was in a totally different location than it is today!! How does this happen? And why does this happen? Let’s take a look. In order for us to get some understanding of how the earth has changed over time‚ we first need to understand some of the things that took place‚ and are still taking place‚ in the earth. What about the internal structure of the Earth? Our best clues about the interior
Premium Geology Earthquake Population density
snow and becomes a formula. This formula sinks into the land (soil mostly) and kills vegetation. The purpose for this exit project experiment is to find out what are the affects of road salt on plants. The reason for doing this lab is to find out what a certain concentration of road salt will have an affect on a specific type of plant. Also to see what changes will occur like the color of the plant will change or the height of the plant. We are doing this to see what happened
Premium Water Snow Chemistry
but one difference that could be proposed between them is the rate of nucleation when the different solutions are super cooled. According to one study‚ “Supercooling occurs when a liquid does not freeze although its temperature is below its freezing point” (Gholaminejad & Hosseini‚ 2013). Many experiments have been conducted on this area of study‚ but their experiments were limited because distilled water was the only type of aqueous solution that was used. One research study has been conducted by
Premium Chemistry Liquid Melting point
CHM113 summer 2014 Name: __________________________ EXAM 4 SHOW YOUR WORK 1) Of the molecules below‚ the bond in __________ is the least polar. A) HBr B) HI C) HCl D) HF E) H2 2) Ethanol (C2H5OH) melts at -114°C. The enthalpy of fusion is 5.02 kJ/mol. The heat capacity of solid and liquid ethanol are 0.97 J/g-K and 2.3 J/g-K‚ respectively. How much heat (kJ) is needed to convert 25.0 g of solid ethanol at -135°C to liquid ethanol at -50°C? A) 207.3 B) -12.7 C) 6.91 D) 4192 E)
Premium Molecule Chemistry Melting point
water that will turn into ice and see what chemical reaction does different types of salt have on the ice. Salt melts ice mainly because adding salt lowers the freezing point of the water. Pure water freezes at 32°F (0°C). Water with salt (or any other substance in it) will freeze at some lower temperature. The normal freezing point of water is 0 degrees Celsius‚ so if the temperature is above that then ice will melt. When salt and water are mixed together‚ the salt dissolves‚ which means the salt
Premium Water Solid Temperature
cup water in each 2. Take one teaspoon of salt and mix it in one of cups 3. Put both cups in the freezer 4. Observe. Conclusion: When salt is added to water it slows the freezing process down‚ therefore the freezing point of tap water is higher than the freezing point of salt water. Hypothesis: If... ‚ then... Materials: 1. 2 Plastic cups 2. Tap Water 3. Teaspoon 4. Bag of salt 5. Freezer 6. Clock 7. Paper 8. Pencil Procedures: 1. Take your plastic
Premium Water Temperature Solid
metals. f) Hot Tearing: This defect also called hot cracking occurs when the casting is restrained or early stages of cooling after solidification. The defect is manifested as a separation of the metal (hence the terms tearing or cracking) at a point of high tensile stress caused by metal’s inability to shrink naturally. In sand casting and other expandable mold processes‚ compounding the mold to be collapsible prevents it. In
Premium Sand Melting point
Have you ever seen dry ice‚ well let me show you. To measure the evaporation rate it is important to know that a half pound of dry ice will be placed outside and timed. The same thing will happen but in a cool room. If the dry ice is -109.3°F then it will evaporate in any condition warmer. The hypotheses is that the dry ice in the outside will evaporation faster. It is important to understand this because if you are trying to store dry ice and you put it in a freezer it will still evaporate. So in
Premium Water Temperature Melting point