OBJECTIVES: 1. to investigate the heating process for solid dodecanoic acid 2. to investigate the cooling process for liquid dodecanoic acid 3. to determine and compare the melting and freezing points of dodecanoic acid SUPPLIES: Equipment ring stand buret clamp hot plate test tube (18mm * 150 mm) assembly (half full with solid dodecanoic acid with thermometer embedded) beaker (400 mL) thermometer for water bath lab apron safety goggles Chemical Reagents dodecanoic acid‚ C11H23COOH
Premium Melting point Liquid Temperature
Woody Point Festival Case Analysis Introduction With its inception in 2004‚ the Writers at Woody Point Festival have become an ever increasingly popular annual literature festival for Newfoundland’s west coast. The festival has grown each year and has now reached the point where council believes a formal marketing strategy and plan is necessary for the festivals short and long term economic sustainability in the ever-increasingly competitive literature festival market. To create the marketing
Premium Term Event planning Festival
Khoa Kirk Hoang OCHEM 262 Lab: Exp 35- Oxidation + Reduction Tablular Data Pre-Weighted Flask | Product + Flask | Product | % Yield | 5.36g | 5.401g | 0.041g | 41% | (60-70% = Acceptable) Actual Melting Point | Experimental Melting Point | 212C | 199.8 | ------------------------------------------------- (10C-15C variations acceptable) Reasons %yield: A reason that our percent yield is lower then what is acceptable can be due to various reasons. First‚ the amount of product we
Premium Camphor Melting point Carbon dioxide
determining the identity of the unknown sample are listed in Table 1. Density (g/cm3) Molecular Weight (g/mol) Melting Point (ºC) Polypropylene 0.905 42.08 170 Polyethylene 0.92 28.05 130-145 Polycarbonate 1.2 158 310 Polystyrene 1.05 104 240 Polyvinyl chloride 1.4 62.5 160-172 Table 1 Properties for five known polymers (Callister 737-775) The melting temperature of a polymer is the point at which it transforms from the solid form to a viscous liquid in which there is little molecular order (Callister
Premium Plastic Polymer Melting point
Physical Lab 15: Chemical and Physical Properties Experiment 1: Physical Properties of Water Data Table 1: Melting Point Data Initial Time Final Time Observations Weigh Boat A 5:37 pm 7:00 pm 10 min- little puddle just started melting. 20 min- puddle under ice is a little bigger. 30 min- ice is melting more and getting a wetter appearance. 40 min- about half way melted. 50min- still slowly melting a bit more than half gone. 60 min- about a quarter of the cube remains. 70 min- a little les than a
Premium Melting point Water Sodium chloride
virgin polycrystalline silicon which are placed in a quartz crucible along with small quantities of elements called dopants - the most common of which are boron‚ phosphorus‚ arsenic and antimony. The materials are heated to a temperature above the melting point of silicon‚ 1420 degrees Celsius. Once the polycrystalline and dopant combination has been liquefied‚ a single silicon crystal‚ the seed‚ is positioned on top of the melt‚ barely touching the surface. The seed has the same crystal orientation required
Premium Solid Silicon Materials science
Ontario regulation 455/07 and the demerit point system The Ontario regulation 455/07 and the demerit system work together in order to promote safe driving on roads and to discourage dangerous activities on roads. Regulation 455/07 is a very detailed article containing rules against extreme drivers. It contains rules prohibiting stunts and racing on roads. Withing the article‚ stunts are defined as drivers attempting to lift one or all of the vehicle’s wheels off of the road‚ to lose traction
Premium The Road Crime Automobile
PREPARATION OF ASPIRIN AND DETERMINATION OF THE MELTING POINT Ferrer‚ Lara Melissa V. Faculty of Engineering University of Santo Tomas Manila‚ Philippines ABSTRACT This experiment involved three steps: synthesis of aspirin‚ isolation and purification‚ and the estimation of purity of the final product. The synthesis involved the reaction of salicylic acid and acetic anhydride in the presence of a catalyst‚ phosphoric acid‚ H3PO4. When the aspirin was prepared‚ it was isolated and filtered. The percentage
Premium Aspirin Acetic acid Acetic anhydride
the esterification of p-aminobenzoic acid with ethanol. The percent yield of crude product was determined to be 21% and the melting point was recorded at 86.2°C ± 0.2°C‚ with a 6.3% error from 92°C‚ the literature melting point of pure benzocaine. The crude product was then recrystallized to improve the purity of benzocaine and 57.4% was recovered. The new melting point range was measured at 89.1°C ± 0.3°C‚ which has a 3.15% error. The infrared spectrum of the recrystallized product was measured
Premium Cocaine Local anesthetic
MME 3210 Materials Processing Techniques Laboratory Assignment – Sand Casting of an Aluminium 13wt% Silicon Alloy 1) Process Attributes Waste shown yellow* Waste shown yellow* After taking part in the sand casting laboratory session it was made clear that the process possessed many advantages and disadvantage‚ both from the process itself and from the final part produced. Observing the process step by step it was noted that the tasks carried out by the operator were not very difficult
Premium Melting point Solid Liquid