TITLE PAGE PREPARATION AND CHARACTERIZATION OF SODIUM SALICYLATE OINTMENT INTENDED FOR TOPICAL AND SYSTEMIC DELIVERY BY MUOBIKE MAKUO 2005/136609 IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE AWARD OF DEGREE OF BACHELOR OF PHARMACY (B. PHARM) OF THE UNIVERSITY OF NIGERIA‚ NSUKKA. DEPARTMENT OF PHARMACEUTICAL TECHNOLOGY FACULTY OF PHARMACEUTICAL SCIENCES UNIVERSITY OF NIGERIA‚ NSUKKA. PROJECT SUPERVISOR: DR. I. V. ONYISHI OCTOBER‚ 2012. APPROVAL PAGE This is to certify
Premium Solubility Melting point PH
used to measure temperature. The extremely fine tube (narrow bore) of a thermometer is called a capillary. The boiling point of water (or condensing point of steam) is 100oC or 212oF or 373 K. The freezing point of water (or melting point of ice) is 0oC or 32oF or 273 K. These temperatures are typically used in the calibration of thermometers and are known as the fixed points. The temperature range that is typically marked on a laboratory thermometer is −10oC to 110oC. Thermometric liquids are
Premium Temperature Liquid Thermodynamics
container’s ice has been half melted. To keep this experiment valid I will keep the amount of ice‚ the time‚ and the amount of materials the same. In my experiment I will test to see what materials will change the ice to its freezing point depression state where it will be melting and there will be ice surrounded by water it just melted off. A few more scientific concepts that relate to this are the Freezing
Premium Water Temperature Chemistry
advantages of the one pierce mold casting include simplicity‚ low cost‚ and no seam lines in finished patterns. As with all manufacturing methods there some disadvantages to casting that include it can only be used with non-ferrous metals that has low melting temperature and long cooling time. As for the material used which consisted of a silicone mold making rubber and a special chemical composition (catalyst) with a usage ratio of 10 to 1. The calculate amount used for the silicone rubber was 918 g
Premium Recycling Melting point Polymer
Acetone has a molar mass of 58.1 g mol-1 and a density of 0.787 g cm-3. Chloroform has a molar mass of 119.4 g mol-1 and a density of 1.499 g cm-3. Estimate the volume of the above mixture using this information. 3. Calculate the molal freezing point depression constant Kf for 1-octadecanol using: Tf = 57.95 oC‚ Hfus = 74.047 kJ mol-1‚ and M = 270.5 g mol-1. ΔTf = Kf m 4. A polymer chemist dissolves 20.00g of polystyrene in 1.000L of benzene. The solution is found to generate an osmotic
Premium Thermodynamics Volume Temperature
find the quality of NaCl as a deicer. These experiments included testing the freezing point depression of NaCl in solution at two different concentrations‚ testing for the H of an aqueous NaCl solution‚ and combining NaCl with MgCl2 in an aqueous solution to test for freezing point depression. Through these various experiments we found NaCl to be the best deicer for our region due to its proficient freezing point depression and its cost efficiency. Introduction As scientists we were given the
Premium Sodium chloride Chemistry Concentration
proves Explanation 3 true because it states that the high conductivity of the aluminium compared to the plastic is why the ice melts so fast on it. This evidence isn’t so obvious to some‚ who think that there is a different explanation to the ice melting faster on block a than block b. Some believe that the ice melts faster on block a because the aluminum absorbs the cold of the ice. According to the Molecular Kinetic Theory of Matter‚ “The motion of the particles that make up an object decreases
Premium Water Melting point Temperature
CHEM 3411‚ Fall 2010 Solution Set 5 In this solution set‚ an underline is used to show the last significant digit of numbers. For instance in x = 2.51693 the 2‚5‚1‚ and 6 are all significant. Digits to the right of the underlined digit‚ the 9 & 3 in the example‚ are not significant and would be rounded off at the end of calculations. Carrying these extra digits for intermediate values in calculations reduces rounding errors and ensures we get the same answer regardless of the order of arithmetic
Premium Concentration Mole Pressure
MME 3210 Materials Processing Techniques Laboratory Assignment – Sand Casting of an Aluminium 13wt% Silicon Alloy 1) Process Attributes Waste shown yellow* Waste shown yellow* After taking part in the sand casting laboratory session it was made clear that the process possessed many advantages and disadvantage‚ both from the process itself and from the final part produced. Observing the process step by step it was noted that the tasks carried out by the operator were not very difficult
Premium Melting point Solid Liquid
procedure by inserting the ice cube into the beaker filled with vegetable oil‚ the dullness and boring state also began to flow. We sat there watching for a good five minutes before any visual reaction was taking place. The ice cube was actually melting in the oil; however‚ the water‚ representing a simple start for the procedure‚ was not mixing with oil. This aroused us with many questions and observations such as “Why is the water not mixing with the oil?” and “Does It have anything to do with
Premium Water Solid Chemistry