Automotive Engineering Advising Document Master of Engineering in Automotive Engineering CURRICULUM Systems Engineering Core Engineering Electives Management and Human Factors Automotive Engineering Seminar and Capstone Project TOTAL PROGRAM: Semester Credit 9 9 6 6 30 The M. Eng. Degree in Automotive Engineering requires a total of 30 credits—27 of which must be letter (A-E) graded. A minimum grade point average of 5.0/9.0 (“B” average) is required for graduation. Of the 30 credit hours‚ 24
Premium Internal combustion engine Engineering Control theory
420 PROCEEDINGS OF THE IEEE‚ VOL. 70‚ NO. 5‚ MAY 1982 Silicon as a Mechanical Material KURT E. PETERSEN‚ MEMBER‚ IEEE Abstract-Single-crystal silicon is being increasingly employed in a variety of new commercial products not because of its well-established electronic properties‚ but rather because of its excellent mechanical properties. In addition‚ recent trends in the engineering literature indicate a growing interest in the use of silicon as a mechanical material with the ultimate goal
Premium Silicon
ALL INDIA SHRI SHIVAJI MEMORIAL SOCIETY’S COLLEGE OF ENGINEERING‚ PUNE. BY MAYUR WAKHARE AND ADITYA MUKHEDKAR mayurwakhare@gmail.com mukhedkar.aditya@gmail.com INDEX * INTRODUCTION.......................................................3 * WHY ROBOTS AND AUTOMATION IN BIOLOGY AND MEDICINE.......................................................3 * ROBOTCS TOOLS‚ DEVICES‚ SYSTEMS..............4 * KEY TECHNOLOGY........................................
Premium Biology Molecular biology Protein
Manufacturing Technology MEC205 Non Traditional machining processes Water jet machining Electro chemical machining Turbine blade EDM EDM products Chemical machining Product from water jet machining Chemical machining structure Introduction Machining is a broad term to describe removal of material from a workpiece. 1. Machining categories: – Cutting involves single-point or multipoint cutting tools‚ each with a clearly defined geometry. 2. Abrasive processes:
Premium Machining
DESIGN OF A SINGLE AXIS RATE TABLE TO MEASURE ANGULAR MOTION OF A MEMS-BASED GYROSCOPE Final Year Design Project Report Submitted by M. Usman Ehsan Saad Mirza Sarah Nusrat S. Nabeel Hassan Faculty of Electronic Engineering Ghulam Ishaq Khan Institute of Engineering Sciences and Technology. May 2009. Abstract The following report deals with the development of a rate table at GIKI for the purpose of testing MEMS-based gyroscopes being developed here. This report consists of the initial
Premium Electric motor
Study of passive filter characterization for PCB application Chapter 1: Introduction Project Description Passive filters are relatively simple electronic part that consists with resistors‚ capacitors‚ and inductors. The function of the passive filter is to allow a certain range of frequencies to pass‚ can be used to separate signals‚ passing those of interest‚ and also can reject noise and attenuating the unwanted frequencies. In this project‚ there are three type of passive filters that
Premium
Princekumart9@gmail.com‚ Institute of Technology &Management‚ Bhilwara 1 ABSTRACT Nanorobotics‚ just as with all nanotechnology is still in very early stages of development and as such is largely based within electronic engineering and physics and concerns micromachining‚ microelectromechanical systems (MEMS)and Scanning Probe Microscopy methods. Research into any particular method for creation of nanorobots will largely depend on the group carrying out the research rather than the subject within which they are
Premium Nanotechnology Blood Blood vessel
3.2 “Lab-on-a-Chip” A Lab-on-a-Chip (LOC) device‚ also known as a micro-total-analytical system (microTAS) or microfluidics device‚ is a device that can integrate miniaturized laboratory functions (such as separation and analysis of components of a mixture) on a single microprocessor chip using extremely small fluid volumes on the order of nanoliters to picoliters. From a technology categorization perspective‚ LOCs can be viewed as a subset of microelectromechanical systems (MEMS) and combine
Premium Cantilever
Digital Micromirror Device ( Chunhai Ji Introduction The applications of large screen‚ high brightness electronic projection displays include (1) electronic presentations‚ (2) entertainment‚ (3) status and information and (4) simulation (e.g.‚ training‚ and games). So far the electronic presentation market is being driven by the pervasiveness of software that has put sophisticated presentation techniques into the hands of the average PC user. Normally three of projection display techniques
Premium Digital Light Processing Light Color
Content 1. Abstract……………………………………………………….. 1 2. Introduction…………………………………….…………….. 2 3. Design & Analysis…..……………………………………….. 3 4. Result ………………………………………………………… 10 5. Conclusion…………………………………………………..... 10 Smart Dust Shilpa Nagod Page 1 of 10 SMART DUST 1.Abstract ’Smart’ dust’ is a minute grain of silicon that spontaneously assembles‚ orients and senses its local environment‚ a first step toward fan development of rebels the size of sand grains that could be used in medicine‚ bioterrorism
Premium Wireless sensor network Optical fiber Power