Melting Points Elizabeth McGrail Organic Chemistry I 25 January 2013 ABSTRACT The objectives of this lab are‚ as follows; to understand what occurs at the molecular level when a substance melts; to understand the primary purpose of melting point data; to demonstrate the technique for obtaining the melting point of an organic substance; and to explain the effect of impurities on the melting point of a substance. Through the experimentation of three substances‚ tetracosane‚ 1-tetradecanol and
Premium Chemistry Molecule Temperature
Lab One – Diffusion and Osmosis SECTION ONE: Methods Lab 1 – Diffusion and Osmosis can be broken down into four parts (A‚ B‚ C‚ and D). Lab 1A – Diffusion In this exercise‚ we tested diffusion through dialysis tubing. This was done through a demo with the teacher‚ rather than individually in groups. First‚ a piece of 2.5cm dialysis tubing was obtained. Then one end was folded and clipped securely so that a solution poured into the bag would not leak out. Next‚ the other side of the bag was
Premium Osmosis Diffusion Chemistry
Lab 1: Heart Rate Lab (Revised Fall 2010) Lab 1. Heart Rate‚ Physical Fitness‚ and the Scientific Method Prelab Assignment Before coming to lab read carefully the following pages on the scientific method and then answer the prelab questions at the end of this lab handout. Be prepared to discuss and/or hand in your responses to the prelab questions at the start of lab. Introduction Biology is a dynamic field of study whose aim is to unravel the mysteries of life itself. Throughout history‚ humans
Premium Cardiology Blood Artery
Lab Report Assistant This document is not meant to be a substitute for a formal laboratory report. The Lab Report Assistant is simply a summary of the experiment’s questions‚ diagrams if needed‚ and data tables that should be addressed in a formal lab report. The intent is to facilitate students’ writing of lab reports by providing this information in an editable file which can be sent to an instructor
Premium Laboratory Experiment Chemistry
NT2640 Unit 9 Labs Detailed Lab Step Answers: 25 answers Step 6. Full duplex 100Mb/s Step 10. show interfaces status Detailed Lab Step Answers: Step 5. 0200.0000.AAAA Fa0/11 0200.0000.BBBB Gi0/1 0200.0000.1111 GI0/2 0200.000.2222 Gi0/1 Step 9. 0200.0000.2222 Fa0/12 0200.0000.1111 Gi0/1 0200.0000.AAA Gi0/1 0200.0000.BBBB Gi0/1 No Detailed Lab Step Answers: Detailed Lab Step Answers: Step 5.
Premium IP address User interface Internet Protocol
constant. Use potassium chloride with a known conductivity as a standard solution. The conductivity measurements are not appropriate to compare between two electrolyte solutions because of the high dependant towards solution concentration. The molar conductivity (Λm) measurements would be more appropriate. Λm could be determined from the conductivity value: [pic] where C is the electrolyte concentration In mol/L. the unit is S cm2mol-1 If the dependant of conductivity towards concentration
Premium Electrochemistry Sodium chloride Physical chemistry
melt. This only works‚ however‚ if the temperature outside is at or near freezing. If it is too cold outside‚ the ice itself becomes very dry and salt is not as effective in melting it. Salt Reduces Freezing Temperature of Water * Salt works by lowering the freezing temperature of water. Salt water needs to reach a colder temperature than pure water to freeze. This is why salted ice on roads that are near the freezing temperature of pure water (32 degrees Fahrenheit) will melt and not refreeze
Premium Water Melting point Snow
Purpose: a) Determine the melting points of two organic compounds known to have the same melting range when pure. b) Determine the mixture melting point of a mixture of the two pure compounds. c) Identify an unknown organic compound by determining its melting point and mixture melting point. Procedure and Observations: Using the procedure outlined in Appendix A of the Lab Manual‚ approximately equal samples of p-Nitrophenol and acetanilide‚ which are known to have the same melting range
Premium Chemical compound Chemical substance Temperature
Investigation of the point of incipient plasmolysis of onion cells (Allium cepa) using NaCl (Sodium Chloride) concentrations of 0.1M‚ 0.2M‚ 0.3M‚ 0.4M‚ 0.5M‚ 0.6M Design Research Question (Aim): The aim of this lab was to determine the point of incipient plasmolysis of onion (Allium cepa) cells using Sodium Chloride (NaCl) concentrations of 0.1M‚ 0.2M‚ 0.3M‚ 0.4M‚ 0.5M‚ 0.6M. Hypothesis: When the water concentration of a solution outside the cell is lower than the concentration inside the cell
Premium Osmosis Concentration Cell wall
Spectroscopy‚ Boiling point and Melting point. Introduction: - Infrared spectroscopy has also made a break though in medicine. It used to evaluate the kidney stone diseases thus broadening the use of IR in different ways. The purpose of this lab experiment is to identify the unknown solutions using the Infrared Spectroscopy (IR)‚ boiling point‚ and melting point (1). The IR helps to determine the compounds such as a functional group. In order to analyze the compound‚ IR and melting point work the best together
Premium Bacteria Chemistry Temperature