Lithium‚Sodium‚Potassium‚Rubidium‚Caesium and Francium are all part of group 1.They are metals that can be easily cut.After being cut‚it is shiny but it quickly tarnishes due to the fact that the metal reacts quickly with oxygen or water.The shiny surfaces of Sodium quickly tarnishes more quickly than Lithium and Potassium more tarnishes more quickly than Lithium.This shows that the reactivity increases as we move down the group. Figure 1 Elements Melting point Boiling point Thermal
Premium Chemical element Periodic table Chemistry
the Rate of Reaction Between HCl and Sodium Thiosulfate Chemistry Lab report Aim: The aim of this experiment is to determine how concentrations of HCl acid affect the rate of reaction when reacted with Sodium Thiosulfate (Na2S2O3). This experiment would require measuring the mass of the reaction over a period of time to be able to determine the rate of the reaction. Safety Precautions: In this experiment‚ SO2 gas is produced from the reaction between Sodium Thiosulfate and HCl‚ and this can be dangerous
Premium Chemical reaction Chemistry
Title: Reaction of Iodoethane with Sodium Saccharin- Ambient Nucleophile Dates Performed: February 21 + 28‚ 2013 Date Submitted: March 14‚ 2013 Abstract: The product ratio of N-ethylsaccharin to O-ethylsaccharin that occurred due to alkylation with iodoethane at 80 oC was determined to be 81.5% to 18.5%‚ respectively‚ based on an analysis of the 1H NMR spectrum that was collected. The melting point range of 87.8-94.7 oC also indicated that the mixture was largely composed of N-ethylsaccharin
Premium Nucleophile
water as well as the density was calculated. The same process was performed to calculate the density of an unknown substance. The third part Section C 5-25% of sodium chloride was prepared by the instructor. For each percent concentration of sodium chloride a 25 mL was prepared. Weighing the graduated cylinder before and after the sodium chloride was transferred the density were calculation. Pre- Laboratory Questions: 1. A metal sphere weighing 15.45 g is added to 21.27 mL of water in a graduated
Premium Sodium chloride Density Volume
Week 10: Oxidation and Reduction Reactions: The Reactions of Copper Data: Part I: Preparing a solution of copper (II) nitrate Initial mass of copper wire: .520g Mass of copper wire after vigorously scouring: .518g Observations of Copper (II) ribbon mixed with HNO3: Solution turned green. Thick brown gas formed. Copper (II) bubbled vigorously. Cu (II) dissolved‚ solution appeared green/blue. After the addition of H2O a blue crusty precipitate formed. Part II: Synthesis of solid copper
Premium Copper Sulfuric acid Zinc
Results and discussion: I. a. How would you compare that relative reactivity of Na and k -Sodium and potassium react somewhat similar when reacting with water however they are slightly different. Sodium moves because of the hydrogen coming off of it and has a low melting point while potassium’s reaction is faster and enough heat is produced to set light to the hydrogen coming off of it. Each leaves a pink color hue in the water. Discuss the similarities and differences in the behavior of the metals
Premium Chemistry Chemical reaction Water
a) What other name(s) does this chemical go by? (i.e. synonyms) Other names for sodium bicarbonate are baking soda‚ sodium hydrogen carbonate‚ and carbonic acid sodium. (b) What is the type(s) of hazard associated with this chemical? (i.e. poisonous‚ biohazardous‚ ...) According to the Globally Harmonized System (GHS) of Classification and Labeling of Chemicals‚ sodium bicarbonate has not been categorized as hazardous. (c) What should you do if this chemical splashes in your eyes or is spilled
Premium Chemistry Water Bacteria
PRACTICAL 2: Preparation of sodium hexanitrocobaltate (III) Date: 12 March 2014 INTRODUCTION Sodium hexanitrocobaltate (III) is a coordination complex which has the formula Na3[Co(NO2)6]. This compound is yellow in colour. It consists of a central Co3+ ion surrounded by six nitro ligands [1]. This compound is used as a qualitative test for potassium and ammonium ions (so long as certain other cations are not present) [1]. Potassium and ammonium are insoluble in water‚ while sodium is [1]. Hence‚ the
Free Ion Mole Oxygen
2. Preparation Of 1 M Na2CO3 Molecular mass of Na2CO3 = 106g Mass of salt in 100 ml of 1M solution = 10.6g Weighing of salt using electrical balance * Mass of Na2CO3 + beaker = 78.64g * Mass of beaker = 68.04g * Mass of Na2CO3 = 10.6g 1. 10.6g of Na2CO3 was weighed in a dry beaker. Small amount of distilled water was added and the salt was dissolved. 2. The contents of the beaker were transferred to
Free Laboratory glassware Titration Iodine
liquid soaps‚ shampoos and soft soaps because it produces soap of soft consistency and higher solubility in water. Other raw materials: * Builders These are essentially used to build up soaps. Examples of alkali builders are sodium carbonate‚ sodium silicate and sodium sulfate.
Premium Sodium hydroxide Soap Sodium chloride