A. Goal and Purpose: Session 1: In this lab‚ we will achieve a simple Friedel-Crafts alkylation of anthracene. The choice of anthracene as an aromatic substrate stems from two considerations. First‚ there is a question of regioselectivity. Second‚ anthracene and its derivatives are highly visible under UV light. Session 2: In this lab‚ we will complete a partial conversion of 9-acetylanthracene using m-chloroperoxybenzoic acid (mCPBA). We will also determine by NMR‚ the regiochemistry of the
Premium Sodium Chemistry Temperature
Genetically Modified Organisms INTRODUCTION: The purpose of this lab was to identify if non-labeled food products are actually genetically modified foods. Before we could begin testing this theory we first had to gain an understanding about genetically modified organisms in general. This was rather easy because if you have been to any grocery store lately you have without a doubt seen products with labels saying "GMO-free" or even "contains only non-GMO ingredients." GMO actually stands for
Premium Polymerase chain reaction DNA Molecular biology
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
. If the speed of decomposition of hydrogen peroxide is related to the temperature then in high temperature it will speeds the decomposition of hydrogen peroxide. Materials ● Catalase ● Hydrogen peroxide 3% and 1% ● Forceps ● Filter paper discs ● Water ● Ice ● Water baths ● Vials ● Marking Pencils ● Stopwatch Procedure 1. Set up an ice bath (0°C)‚ a room temp water bath‚ a 37°C bath and a boiling water bath 2. Place 5 ml of catalase at 100 units/ml in each 4 test tubes. Place 1 test tube in each of the
Premium Hydrogen peroxide
recrystallization and how this process removes the impurities from a pure solid compound. The methods used to achieve this objective were also hot vacuum filtration in order to remove suspended solid impurities‚ and isolating the pure acetanilide. In the next lab‚ percent recovered was obtained through weighing the acetanilide sample as well as comparing its melting point range. In this experiment‚ the sample‚ acetanilide was weighted to be 1.523 grams. The sample appeared to be a pale mixture of brown flakes
Premium Water Solvent Chemistry
unknown substance or determine a known substance’s level of purity. When organic substances are mixed together in varying degrees they take on a melting characteristic that is lower and broader than in its pure form. This property was manipulated in the lab to observe the various melting points of Naphthalene and Biphenyl when the percentage of composition was altered. A eutectic point of 45 °C at 52% Naphthalene was determined from the class data. An unknown crystalline substance was identified to be
Premium Liquid Temperature Solid
A. Avril Crayfish Lab Report November 9‚ 2012 Dr. Marvin Results: Figure 1. Firing Rate of Tonic Receptor in Response to Stretch. The correlation between Firing Rate and Stretch of the slow adapting crayfish receptor for four different sets of data is represented in this figure. The recordings are taken at stretches of 2‚ 4‚ 6‚ 8‚ and 10 mm of the crayfish tail. The best fit lines for the different sets of data are as follows: Ali and Emily- Linear best fit line‚ Dave and Laura- Exponential
Premium Action potential Membrane potential Neuron
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume