Lab #3: Assessment Worksheet Lab Assessment Questions: What is the goal or objective of an IT risk management plan? A list of threats A List of vulnerabilities Costs associated with risks A list of recommendations to reduce the risks Costs associated with recommendations A cost-benefit analysis One or more reports What are the five fundamental components of an IT risk management plan? The components of a Risk Management Plan are: Risk Identification Risk Analysis Risk Evaluation
Premium Risk management Risk
this lab because the limiting reactant is the substance that is used up first in a chemical reaction. The amount of product was limited by that reagent. The excess reactants were considered to be the other reagents that were presented in excess of the quantity that was reacted with the limiting reagent. The theoretical yield was determined as the amount of product obtained when the limiting reagent was completely used. The limiting reagent was identified in order to calculate the percent yield of the
Premium Chemical reaction Chemistry Reaction rate
Chromatography Lab Questions Pre-Lab Questions 1. A pencil is used rather than a pen to mark the “starting line” in step two because a pen or marker while be used to place a small dot of ink in the center of the X that is made with a pencil. 2. Capillary action is filling of pores in a solid with a liquid. Capillary action is caused by spotting or absorption and is allowed to seep or flow through. 3. The type of pen that will probably give better separation in this paper chromatography
Premium Pigment Liquid Thin layer chromatography
Samuel Heidenreich Miss.Tatu Biology March 5‚ 2015 Introduction In the Mitosis lab an onion root was observed under a microscope to observe whether or not cell division takes place. Also‚ whether cells replicate in order for it to reproduce. By observing the onion root under the microscope it allows many layers to be looked at through each cell division. The goal of Mitosis is the replication of cells to produce multiple like cells. The steps involved in Mitosis are what is known as
Premium Mitosis Cell cycle Observation
LAB OF ENTHALPY CHANGE IN COMBUSTION Objective: Determine the Enthalpy change of combustion ΔHc of three different alcohols. Methanol‚ Ethanol and Isopropilic acid. Procedure: 1. Fill the spirit micro burner with Ethanol and weight it 2. Pour 100 cm3 of water into the aluminum cup 3. Arrange the cup a short distance over the micro burner 4. Measure the temperature of water 5. When the temperature of the water has risen by 10°C‚ record the temperature. 6. Reweight
Premium Oxygen Ethanol Carbon dioxide
Taylor Hill Lab 6: Enzymes Purpose: The purpose of this lab is to test for enzyme activity‚ look at enzyme specificity‚ and how temperature affects enzyme activity. Hypothesis: I believe that the room temperature activity will produce the most activity. Materials: 3% hydrogen peroxide‚ a household blender‚ potatoes (3 medium size potatoes‚ that are peeled and quartered)‚ tap water‚ 8 test tubes‚ 8 transfer pipets‚ sugar packets‚ salt‚ a small saucepan‚ a refrigerator with a freezer‚ stove
Premium Enzyme Water Catalase
Julie Nguyen Equilibrium Lab 4-28-14 I. Purpose To study the affect of temperature & concentration changes on systems in equilibrium II. Safety Wear apron Wear goggles Do not spill chemicals Clean up after use Wash hands Chemicals are TOXIC (by Britney Spears) III. Procedure A. Iron-thiocyanate equilibrium Pipet .3mL of 1 M iron (III) nitrate and .3 mL of 1 M ammonium thiocyanate. into clean 250 mL beaker. Add 75 mL of DS water. Mix well. Divide the solution into equal
Free Hydrochloric acid Sodium chloride Chemistry
Avenue‚ Manila‚ Philippines cedric_labasan@dlsu.ph Abstract This lab report defines what uniform acceleration is and how to calculate uniform acceleration of a cart rolling down a ramp at different angles and elevations. The experiment will be performed by setting the cart on the track against the end stop and then record this final position on the steel ramp ten times. Once the results are found you can calculate the percent error of the uncertainty values. The uncertainty value is the acceleration
Premium Acceleration Classical mechanics Velocity
Metallographic Observation Metallographic Observation Group # 26 Group # 26 Me 230: Control of Properties of Materials Me 230: Control of Properties of Materials Department of Mechanical and Mechatronics Engineering University of Waterloo Instructor: Caroline Hanson Date: 4‚ April‚ 2013 Department of Mechanical and Mechatronics Engineering University of Waterloo Instructor: Caroline Hanson Date: 4‚ April‚ 2013 Introduction Engineers study the properties
Premium Steel Metallurgy Austenite
Physiology I got to take part in dissecting a cow eye. My lab partner was . The purpose of dissecting the cow eye was to learn and familiarize the class with the structure of the eye and to locate structures. Materials used were the cow eye‚ scalpel‚ probe‚ tweezers‚ scissors‚ dissection tray‚ gloves‚ paperwork / book‚ paper towel‚ ourselves‚ and our lab partner. My data includes the checklist‚ lab sheets‚ drawing‚ picture‚ and my lab report. The first step was to observe the outer structure
Free Eye