Central Philippine University ILOILO CITY‚ PHILIPPINES MATHEMATICS and PHYSICS DEPARTMENT Experiment No.___________________ Name _________________________________________ Course and Year ______________ I. Objective: -To determine and to identify the motion which the metal ball undergoes as it rolls down the acceleration board. II. Materials: Acceleration board‚ cornstarch‚ iron stand‚ clamp with iron bar‚ brass ball‚ PVC pipe‚ meter stick III. Procedure: 1. Using
Premium Light Iloilo City Time
Introduction Bounce Fitness is made up of four fitness centres. Head office is currently established in Cairns‚ Queensland. The other centres are in Brisbane‚ (Queensland)‚ Sydney‚ (New South Wales) and Melbourne‚ (Victoria). It is the intention of the Board of Directors that a new centre will be opened in Perth‚ (Western Australia). It was established in 2001 by Margaret House as a single aerobic studio. After two years membership increases demanded the small leased centre be expanded and
Premium Physical exercise Health club Aerobic exercise
Phil Yu Electrostatics Lab Data Chart Part 1: Trial | Material | Material | Charge (+ or -) | q (nC) | 1 | Glass | Fur | + | 3.108 | 2 | Clear Plastic | Fur | + | 45.07 | 3 | Yellow Plastic | Fur | - | 81.57 | 4 | Glass | Silk | + | 1.979 | 5 | Clear Plastic | Silk | + | 19.60 | 6 | Yellow Plastic | Silk | - | 75.49 | 7 | Glass | Green Cloth | + | 2.914 | 8 | Clear Plastic | Green Cloth | + | 31.09 | 9 | Yellow Plastic | Green Cloth | - | 90.30 | Data Chart Part 2:
Premium Electric charge Concentration
Lab 1 – Measurement of Space and Time Anthony Lucci Lab Partner: Amy Hayes Question 4: Both the height and diameter of the cylinder were taken to find the volume; five times for both measurements. Vernier calipers were used to get these measurements by clamping the cylinder between the jaws of the calipers. By looking at the mark of the zero‚ in relation to the main scale‚ the line best lined up with a line from the main scale was taken down. Getting
Premium Measurement Errors and residuals in statistics Volume
PHYS 211 Physics for Science and Engineering Experiment 1: Projectile Motion Physics Lab Report 3 OBJECTIVE The objective of the experiment is to measure the speed at which a projectile leaves a spring gun and to predict the landing point when the projectile is fired at a nonzero angle of elevation. EQUIPMENT Spring gun Metal ball Protractor Meter stick Ruler Whiteboard markers THEORY Projectile motion is an example of motion with a constant acceleration. In this experiment
Free Newton's laws of motion Force General relativity
Grade 9 Science – Trolley Lab -‐ Luca Weller – AOI: Environment – 17/9/13 D.4 Materials: -‐1 trolley that will be accelerated -‐1 string to connect the trolley and the weights (ca. 2m) -‐1 set of weights that will accelerate the trolley (up to 5N) -‐1 a.m
Premium Acceleration Mass Kinematics
Calorimetry Lab: Determining the Unknown Metal Purpose: To determine the identity of an unknown metal Hypothesis: The unknown metal is Copper Materials: * Safety glasses * Styrofoam cup * Thread or string * Glass rod * Thermometer * 100mL graduated cylinder * Hot plate * Balance * Unknown metal * 300mL beaker Procedure: i. Mass of metal was recorded ii. Water was heated on a hot plate in beaker iii. Temperature was recorded when water reached
Premium Heat Temperature Thermodynamics
How high does a ball bounce? Aim: To see how high the bounce of a ball is. The changed variables are the height of where the ball is dropped from. The independent variables of this investigation. The (dependent) variable that will be measured in this investigation is the bounce height of the dropped ball. This shall be observed with one person dropping the ball from above while another person watches the for the highest point the ball reaches. Three variables that could be affected
Premium Basketball Baseball Atmospheric pressure
white paper‚ metal ball‚ plumb bob. Procedure: In preparation to fire the metal ball from the spring gun‚ we moved the pendulum arm to its maximum position and out the line of fire. We fired the spring gun to get an estimate of where the ball will drop on the floor. We then set up the carbon paper between two sheets of white paper on the floor in the spot that the ball hit the floor. We fired the spring gun 3 times‚ each time using a meter stick to record the vertical distance from the tip of
Premium Classical mechanics Kinetic energy Force
light in a vacuum‚ 3 ×108 ms-1.) 1 3. Estimate the critical angle of incidence for light passing from this plastic to air. light source transparent plastic block Apparatus arranged to measure the critical angle of incidence In your report‚ explain a) why it is convenient to have a semi-circular plastic block b)why the block must be turned through 180° (as shown in the second diagram) to measure the critical angle of incidence c) what is the main difficulty in measuring the angles of
Premium Refraction Snell's law Total internal reflection