Independent Assessment Physics Lab (SL): Cantilever Flexion Cherno Okafor Mr. Ebrahimi SPH4U7 October 21st‚ 2012 Introduction Purpose: The purpose of this Physics Lab is to investigate what factors determine the amount of flexion of the cantilever. Hence‚ the objective is to establish a relationship between the length of a cantilever‚ which may give some insight into the physics of cantilevers. Hypothesis: If one increases the length of a cantilever‚ one would expect there to be an
Premium Orders of magnitude Mass Force
Speed of Sound Lab Report Jamie Cook PHYS 1114: College Physics I Oklahoma City Community College December 10‚ 2013 Purpose: The purpose of this experiment is to measure the speed of sound in air and to determine the effects of frequency on the speed of sound. Apparatus (equipment used): Signal generator: manufacturer- EMCO‚ model number- SS-1‚ range- 20Hz-2MHz‚ least count- 1Hz Frequency meter: manufacturer- DEADALON CORPORATION‚ model number- N/A‚ range-
Premium Sound Speed Wavelength
Lab Report: Projectile MotionChange Launch Angle 03/05/2012 James Allison section 20362 Group 5 James Allison‚ Clint Rowe‚ & William Cochran Objective: In this lab we will compare different parameters of a launched projectile. This includes time of flight‚ initial velocity‚ initial vertical velocity‚ initial horizontal velocity‚ range‚ time of max height. All these data points are collected for 30°‚ 40°‚ 45°‚ 50°
Premium Range of a projectile Velocity Airport
April 29‚ 2014 Abstract The objective project was to use our knowledge of physic properties to create a working car that was powered by a mouse trap. I found that the lighter the car was and the more traction the car had‚ the further it travelled. Introduction The purpose of this project was to create a car that is powered by a mouse trap. We were to use our knowledge of physics laws to make the best car we can. I knew from Newton’s Law‚ F=ma‚ that if my car had a lower
Free Force Classical mechanics Potential energy
(II) Sulfate Wash Bottle Lab Apron 2 Iron Nail Stirring Rod Plastic Gloves 1M Hydrochloric Acid Crucible Tongs Sandpaper or Emery Cloth Distilled Water Centigram Balance Face Shield Drying Oven 1. Find the mass of a clean‚ empty‚ dry 250-mL beaker. Record the mass to the nearest 0.01 g. 2. Add approximately 8 g of copper (II) sulfate crystals to the beaker. Find the mass and record it on the Report Sheet. 3. Add 50 mL of distilled water
Premium
blah i just want to be able to read this essay so I’m sorry if this isdissappointing to you hold on Physics Pre-AP Projectile Motion Lab Report Purpose The purpose of this lab was to determine how angle and gravity affects velocity and range. Procedure Materials Projectile launcher Marble Two measuring sticks Tin foil Pencil Procedure Set the angle of the projectile launcher to 30 degrees (make sure that the bottom of the launcher is even with the desk). Put the marble inside the
Premium Angle Archimedes Force
Blackbody Radiation Lab 11 Go to http://phet.colorado.edu/simulations/sims.php?sim=Blackbody_Spectrum and click on Run Now. 1) In this lab‚ you will use the Blackbody Spectrum Simulation to investigate how the spectrum of electromagnetic radiation emitted by objects is affected by the object’s temperature. In this simulation‚ you can input the temperature and observe the spectrum of the radiation emitted. a) The temperature of stars in the universe varies with the type of star and the age
Premium Infrared Black body Electromagnetic radiation
LAB WRITE- UP NAME: MANOUCHEKA FIDEL DATE: 9/19/14 TITLE: BACK AND FOURTH MOTION PURPOSE (Introduction): To qualitatively analyze the motion of objects that move back and forth. Then analyze and interpret back and forth motion in kinematics graphs. Use kinematic graphs to catalog objects that exhibit similar motion. PRELIMINARY QUESTIONS: Finding the average velocity Do any of the four objects listed above move in similar ways? If so
Premium Classical mechanics Velocity Newton's laws of motion
Kimmi Dodia- Biomedical Science- 1019971 Lab partner- Kim Harcourt Lab report- Experiment 1: Microbial Genetics Abstract The objective of this experiment was to introduce the study of bacterial genetics in order to identify the potency of different mutagenic agents. Our primary aim was to demonstrate the different techniques needed to isolate biosynthetic auxotrophic mutants using chemical‚ physical and transposon mutagenesis. The second aim was to plan and execute an experiment designed
Premium
Introduction The purpose of this lab is to examine the motion of an electron‚ when it encounters a constant magnetic and electric field. We will also observe when the electric field and magnetic field will cancel each other out. This will lead to the electron having no net force acting upon it. By adjusting the values for the magnetic and electric fields‚ we will be able to check the different paths the electron follows. From this data we will be able to calculate the charge-to-mass ratio. Then
Premium Chemistry Electron Magnetic field