10.8 | 10.8 | 10.8 | Results: Calculations: Scale reading of water level for empty test tube: 7.6 cm External circumference of test tube: 5.6cm A=C24π =5.624π =2.50cm Gradient: y2-y1x2-x1 =5.6-85.5-0 =0.44 Errors: * While filling the large test tube with water‚ there were a few air bubbles that did not come off of the walls of the glass until the paperclips were dropped into the small test tube which caused them to raise and made extra water fall which
Premium
of l. ii) Clamp the metal plate to the frame so that the plate protrudes horizontally from the frame. The length d from the edge of the frame to the thread should be 0.24m. iii) Measure and record the value of d. iv) Determine the percentage uncertainty in this value of d. v) Gently displace the pendulum so that it performs small oscillations in a vertical plane perpendicular to the plate. vi) Make and record measurements to determine the period T of these oscillations. vii) Adjust the position
Premium Clock Pendulum Orders of magnitude
damage the spring. The spring will oscillate due to the acceleration‚ by using a stopwatch record the time taken for twenty complete oscillations. Then repeat this whole process with time same size of mass‚ you have to do two trials to narrow the uncertainty. Then add 100 g masses one by one to the mass hanger and record the extension of the spring and the time taken for that size of mass to complete twenty oscillations. You will be given an unknown mass and also record the time taken of that mass to
Premium Measurement Mass General relativity
Introduction In this lab‚ the density of 20 glass beads were determined using two different methods and the results were compared to see how close the values were to each other. In first method the volume of each individual bead was measured using the diameter of each bead‚ along with the mass. In the second method the beads we treated as a whole unit. The total mass was measured and volume was measured based on the amount of water that was displaced in a graduated cylinder. Then‚ the beads
Premium Density Bulk density
Name : Siti Zulaikha Binti Dahalan Matric. No : FIS 1307 3296 Name of Partner : Title of Experiment : Experiment 2‚ Uncertainty and Error Date Of Experiment : 1st October 2013 Course Name and Code : Physics Lab 1 (FP1021) Instructor’s name : Dr. Azah Nik Jaafar Objective 1. To measure Human Reaction Time 2. To find uncertainty and error of a measurement Apparatus 1. Ruler Theory Human Reaction Time is a measure of how quickly human can respond to a particular stimulus. This
Premium Measurement
Lab #1: Projectile Motion Purpose: To determine experimentally the initial and final velocities of an air powered projectile. Hypothesis: If the angle of the rocket is launched at 45 degrees than the distance and velocity will maximize. Materials: Rocket launching platform Rocket launcher Rocket body Air pump Safety goggles Rubber washer Nose cone 40‚ 45‚ 50‚ 55 and 60 angle wooden blocks Measuring wheel Procedure: 1. The rocket was assembled by the rocket launcher
Premium Rocket Hypothesis
Patel Nil Period 7 05/09/13 Static and Kinetic Friction Objectives:- * Use a Dual-Range Force Sensor to measure the force of static friction. * Determine the relationship between force of static friction and the weight of an object. * Measure the coefficients of static and kinetic friction for a particular block and track. * Use a Motion Detector to independently measure the coefficient of kinetic friction and compare it to the previously measured value. * Determine if the
Premium Friction Force Classical mechanics
Height of Ball Drop v/s The Depth of the Crater | By Tejas Shah‚ IBDP Year 1 | | | | | | | * Aim- To find the relationship between the depth of crater and the height from which it is dropped. * Research Question- Does the height from where the ball is released affect the depth of the crater. * Hypothesis- If we increase the height of the drop of the ball; the depth of the crater would increase. This is because as there is loss in potential energy subsequently there
Premium Kinetic energy Energy Potential energy
Grade 11 physics: SPH3U1-01 | Physics Lab Report | Specific Heat Capacity of Brass | | Jin Jin Shi | 2012/12/6 | Instructor: Mr. Nailer | I. Introduction The amount of heat required to raise the temperature of a solid body depends on its change in temperature (ΔT)‚ its mass (m)‚ and an intrinsic characteristic of the material forming the body called specific heat (cp). The heat is calculated from the equation II. Purpose The purpose of this laboratory is to determine
Premium Heat Specific heat capacity Thermodynamics
Introduction The purpose of this lab is to examine the motion of an electron‚ when it encounters a constant magnetic and electric field. We will also observe when the electric field and magnetic field will cancel each other out. This will lead to the electron having no net force acting upon it. By adjusting the values for the magnetic and electric fields‚ we will be able to check the different paths the electron follows. From this data we will be able to calculate the charge-to-mass ratio. Then
Premium Chemistry Electron Magnetic field