Physics Formulas: Mechanics Mechanics is the oldest branch of physics. Mechanics deals with all kinds and complexities of motion. It includes various techniques‚ which can simplify the solution of a mechanical problem. Here are some of the often required physics formulas falling in mechanics domain. Motion in One Dimension The physics formulas for motion in one dimension (Also called Kinematical equations of motion) are as follows. (Here ’u’ is initial velocity‚ ’v’ is final velocity‚ ’a’ is
Free Force Classical mechanics Mass
Name: _________________ Wire Resistance and Ohm’s Law Go to http://phet.colorado.edu/simulations/sims.php?sim=Ohms_Law and click on Run Now. Wire Resistance and Ohm’s Law Procedure Part I Wire Resistance: open the PhET Simulation Electricity‚ Magnets‚ and Circuits Resistance in a Wire. As wire length (cm) increases‚ the resistance (Ω) _____increases_____ As wire area (cm2) increases‚ the resistance (Ω) _______decreases_______ As wire resistivity (Ωcm) increases‚ the resistance
Premium Incandescent light bulb Electric current Volt
through which it swings. Another factor involved in the period of motion is‚ the acceleration due to gravity (g)‚ which on the earth is 9.8 m/s2. It follows then that a long pendulum has a greater period than a shorter pendulum. Before coming to lab‚ you should visit the following web site: http://www.myphysicslab.com/pendulum1.html This simulation shows a simple pendulum operating under gravity. For small oscillations the pendulum is linear‚ but it is non-linear for larger oscillations. You can
Premium Pendulum Classical mechanics Simple harmonic motion
DP Physics IA Thermal physics: Specific Heat Capacity of Metals Introduction: In this experiment we are going to measure the specific heat capacity of a unknown metal. To measure the specific heat capacity we will heat up the metal to certain temperature and release the metal in beaker filled with water. By knowing the mass and temperature of water filled in beaker‚ we will be able to calculate the specific capacity of unknown metal by change in temperature of beaker willed
Premium Heat Thermodynamics Specific heat capacity
INTRODUCTION Surface modification is a miraculous application of Electric Discharge Machining (EDM). It can modify the conductive material surface by both removing material from the surface and depositing material on the surface. It can remove or deposit material from the work surface through controlled electrical sparks by the process of melting and evaporation. The controlled sparks erode material from the work and tool surface within very short intervals of time. Study of surface morphology widens
Premium Electricity Electromagnetism Electric charge
Physics Lab Report: Parallel Force Aim: To test the principle of moments. Apparatus: Metre rule with holes drilled at the 25cm‚ 50cm and 75cm mark‚ 50g masses 50mm long bolt with a diameter of approximately 5mm‚ retort stand‚ boss head and clamp‚ 0-10 N spring balance‚ electronic pan balance ‚wire or string for suspending masses from the metre rule‚ two bulldog clips. Part A: Balancing a constant moment. Procedure: 1. The experiment is set up by first placing the bolt through the rule‚ then
Premium Force Mass Kilogram
Field Note 117: field radius growth is definitely not linear for linear control voltage increase. Ben sat back from the work bench and took several calming breaths. His sandwich sat on the test plate on top of the field projector array. It was a turkey club...the sandwich that is. The test plate was just a paper plate and the field projector array looked like a vintage ham radio and a movie projector had gotten very intimate. He couldn’t deny the results though. Little fella might have a touchy
Premium Magnetic field Standard deviation Arithmetic mean
Downloaded from www.campusportal.com.ng PHYSICS PREAMBLE The syllabus is evolved from the Senior Secondary School teaching syllabus and is intended to indicate the scope of the course for Physics examination. It is structured with the conceptual approach. The broad concepts of matter‚ position‚ motion and time; energy; waves; fields; Atomic and Nuclear Physics‚ electronics are considered and each concept forms a part on which other subconcepts are further based. AIMS The aims of the syllabus are to enable candidates
Free Force Classical mechanics Energy
JPN Pahang Physics Module Form 4 Teacher’s Guide Chapter 1 : Introduction To Physics _________________________________________________________________________________________ CHAPTER 1 : INTRODUCTION TO PHYSICS 1.1 Understanding Physics PHYSICS Mechanical Energy Study of the natural phenomena and the properties of matter. Heat Energy Light Energy Wave Energy Solid Liquid Gas Matter Energy states forms Electrical Energy Nuclear Energy Chemical Energy Properties of
Premium Measurement Orders of magnitude Time
M11/4/PHYSI/SP2/ENG/TZ1/XX 22116511 PHYSICS STANDARD LEVEL PAPER 2 Candidate session number 0 0 Wednesday 11 May 2011 (afternoon) Examination code 2 1 hour 15 minutes 2 1 1 – 6 5 1 1 INSTRUCTIONS TO CANDIDATES • • • • • Write your session number in the boxes above. Do not open this examination paper until instructed to do so. Section A: answer all questions. Section B: answer one questions. Write your answers in the boxes provided
Premium Nuclear fission Binding energy Nuclear power