Purpose: To practice direct and indirect measurement Introduction: Do you think you could measure the average thickness of a sample of M&Ms without directly measuring selected M&Ms? The answer is "yes‚" and in this activity you will make direct and indirect measurements of the thickness of M&Ms. You will compare the results and evaluate the reliability of each method of measurement. Be sure to view the tutorial on the proper use of the vernier caliper. Please re-visit the information on when
Free Measurement Volume Units of measurement
Spokane‚ Washington. Viney and Fenton (1998) defined the term electrophoresis as‚ “the migration of charged particles through a static medium under the action of an applied electric field (p. 576). Just from this definition‚ it is clear that numerous physics concepts can be used to help explain why electrophoresis works. First‚ I will discuss charge and electric fields and how these principles are utilized in gel electrophoresis. This will be followed by a
Premium Electric charge Electromagnetism Electron
Motion of the Cars In this part of the experiment‚ we are trying to figure out how fast each of the cars are moving using our own measurements. We are also asked to make a mathematical equation that describes the motion. What we plan to do is use 2 meter long meter stick to measure the distance of the cars and record the position at each time interval. After that an average velocity can be found. After we used the average velocity‚ we were able to put it into the equation of a line formula and
Premium Time Measurement Place
Torque and Equilibrium Purpose: Apply principle of static equilibrium to determine a coefficient of friction. Research Question: What is the coefficient of friction between a meter stick and wall? Hypothesis: Tying a piece of string on to the end of a meter stick‚ put the other end of the meter stick against the wall so that the meter stick is horizontal and does not slide down the wall. Hang a weight on the meter stick sliding it to a point where the meter stick is about to come off from
Premium Mass Force Kilogram
Conclusion: Category 1: Momentum was found that after the collision was less than before the collision by 10%. This was not what has been expected‚ so the difference was fairly significant. This happened because of friction‚ when the two pucks collided‚ they have lost a bit of their momentum‚ so the momentum after the collision differed. Kinetic energy differed more than what was expected‚ it was significantly less after the collision‚ the difference before and after the collision was 63.7%‚
Premium Mass Classical mechanics Introductory physics
Parallel Forces Objective: Find FA and FB on the apparatus which are parallel to both Fulcrum A and B. Calculations: Theoretical FB Στ = 0 +FB 0.5 - (0.1kg x g x 0.1m) - (0.2kg x g x 0.4m) - (0.05kg x g x 0.7m) - (0.1kg x g x 0.3m) = 0 -[{(0.1kg x 0.1m) + (0.2kg x 0.4m) + (0.05kg x 0.7m) + (0.1kg x 0.3m)}x 9.8] + 0.5FB = 0 0.5FB = [(0.1 x 0.1) + (0.2 x 0.4) + (0.05 x 0.7) + (0.1 x 0.3)]x 9.8 FB = FB = 3.04 N Experimental FB FB = mpanB g - mfulcrumB g FB = (0.385kg x 9.8)
Premium Experiment Theory
Physics Laboratory Report Sample PHY 223 Lab Report Newton’s Second Law Your Name: Partner’s Full Name(s): Date Performed: Date Due: Date submitted: Lab Section: (number) Instructor: (Name) Introduction We verified Newton’s Second Law for one-dimensional motion by timing an accelerated glider moving along a flat track. We varied both the accelerating force and the mass of the glider. We found that for a given force the acceleration of the glider was inversely proportional to the mass of the glider
Premium Mass Classical mechanics Force
Name: _________________ Wire Resistance and Ohm’s Law Go to http://phet.colorado.edu/simulations/sims.php?sim=Ohms_Law and click on Run Now. Wire Resistance and Ohm’s Law Procedure Part I Wire Resistance: open the PhET Simulation Electricity‚ Magnets‚ and Circuits Resistance in a Wire. As wire length (cm) increases‚ the resistance (Ω) _____increases_____ As wire area (cm2) increases‚ the resistance (Ω) _______decreases_______ As wire resistivity (Ωcm) increases‚ the resistance
Premium Incandescent light bulb Electric current Volt
DP Physics IA Thermal physics: Specific Heat Capacity of Metals Introduction: In this experiment we are going to measure the specific heat capacity of a unknown metal. To measure the specific heat capacity we will heat up the metal to certain temperature and release the metal in beaker filled with water. By knowing the mass and temperature of water filled in beaker‚ we will be able to calculate the specific capacity of unknown metal by change in temperature of beaker willed
Premium Heat Thermodynamics Specific heat capacity
Physics Lab Report: Parallel Force Aim: To test the principle of moments. Apparatus: Metre rule with holes drilled at the 25cm‚ 50cm and 75cm mark‚ 50g masses 50mm long bolt with a diameter of approximately 5mm‚ retort stand‚ boss head and clamp‚ 0-10 N spring balance‚ electronic pan balance ‚wire or string for suspending masses from the metre rule‚ two bulldog clips. Part A: Balancing a constant moment. Procedure: 1. The experiment is set up by first placing the bolt through the rule‚ then
Premium Force Mass Kilogram