CE121: Construction Materials Laboratory Report No. 1 Particle Size Distribution Van Joseph E. Casalme 2010-14928‚ BS Civil Engineering Institute of Civil Engineering‚ College of Engineering University of the Philippines Diliman‚ Diliman Quezon City 1101 Submitted to: Engr. Christian R. Orozco ABSTRACT This test (ASTM C136-06) determines the grading of materials being used as aggregates using two parameters (coefficient of uniformity and gradation) from particle-size distribution
Premium Sieve analysis Particle size distribution Construction aggregate
Solute Concentration of Potatoes Lab #1 Purpose: To find the molarity/concentration of potato cytoplasm. Materials: As on page 1 in the lab handout. Procedure: As on page 1 in the lab handout. Data and Observations: Test Tube # | Concentration of sucrose solution (mol/L) | Initial Mass (g) | Final Mass | Percentage change in mass | 1 | 1.0 mol/L | 3.00g | 2.25g | -25.0% | 2 | 0.9 mol/L | 2.70g | 2.07g | -23.3% | 3 | 0.8 mol/L | 2.92g | 2.25g | -22.9% | 4 | 0.7 mol/L | 2.60g
Premium Concentration Osmosis Chemistry
Acid Base Titration Purpose: The purpose is to calculate the molarity of a NaOH solution by titrating the base with 5mL of standard HCl solution in each trial. By adding the base with unknown molarity to the acid with 0.10M the molarity of NaOH can be calculated. The base‚ NaOH‚ helps bring the pH of the acid‚ HCl‚ closer to seven‚ which neutralizes it. When using the buret the amount of NaOH used is able to be determined. Then by writing a balanced chemical equation and using the titration
Premium Titration Sodium hydroxide Acid
Bubble Inside a Bubble Materials • • • • • • • • Granulated sugar (we had our best results using Imperial Sugar and Dixie Crystals) Dish soap Water Tablespoon Scissors Pipette Cup Adult supervision Bubbles form because of a combination of water’s hydrogen bonds and the oily film you can see shimmer in the light. The oily film you see is actually two separate layers of soap attached to‚ and surrounding‚ hydrogen-bonded water. Solar Oven S’mores Materials • Pizza box • Two clear sheet protectors
Premium Oxygen Thermodynamics Water
inclined forces are applied to the truss‚ thereby simulating various load cases. The occurring tensile and compressive forces in the bars are recorded by means of strain gauges. Computerised evaluation is provided by measurement amplifier FL 151. The software is used to manage the measurement data and provide graphical representation of the bar forces. The software features a comprehensive help function. The various elements of the experiment are clearly laid-out and housed securely in a storage system
Premium Beam Force Truss
Abstract This lab’s purpose was to test the patterns of percolation in various places. This lab tested how soil would absorb water based on different places. Distance from a group of trees‚ distance from a swamp‚ and different types of soil were tested. From the results collected‚ you can not prove‚ but you can infer that the ability to absorb increases as you go farther away from a swamp‚ and a group of trees. The ability to absorb also increases based on how much silt is in soil. Introduction
Premium Soil Surface runoff Digestion
Motion of the Cars In this part of the experiment‚ we are trying to figure out how fast each of the cars are moving using our own measurements. We are also asked to make a mathematical equation that describes the motion. What we plan to do is use 2 meter long meter stick to measure the distance of the cars and record the position at each time interval. After that an average velocity can be found. After we used the average velocity‚ we were able to put it into the equation of a line formula and
Premium Time Measurement Place
Abstract……………………………………………………………………………………………2 Introduction………………………………………………………………………………………..2 Background………………………………………………………………………………..2 Objectives…………………………………………………………………………………2 Scope………………………………………………………………………………………3 Theory review……………………………………………………………………………………..3 Design of report…………………………………………………………………………………...5 Procedures…………………………………………………………………………………………5 Results……………………………………………………………………………………………..6 Discussion…………………………………………………………………………………………6 Conclusion………………………………………………………………………………………...7 Reference………………………………………………………………………………………
Premium Fluid dynamics
simple mechanisms used to convert rotary motion into oscillating linear motion and vice-versa. The first of these is the slider-crank - a mechanism widely used in engines to convert the linear thrust of the pistons into useful rotary motion. In this lab we will measure the acceleration of the piston of a lawn mower engine at various speeds. The results exemplify a simple relation between speed and acceleration for kinematically restricted motions‚ which will discover. An adjustable slider-crank apparatus
Premium Internal combustion engine Classical mechanics Crankshaft
Coulomb’s Law Purpose: The purpose of this lab was to demonstrate that the force between two stationary charges is directly proportional to the product of the charges and inversely to the square of the distance between them. Coulomb’s law tells us that the force between two charges depends (1) linearly on the strength of each charge‚ and (2) inversely on the square of the distance between them. Mathematically we would write this as . Procedures Part1 Begin by removing the right side
Premium Electric charge