Date report submitted: June 18‚ 2015 Title: Lab Techniques and Measurements PURPOSE: The purpose of this experiment is for the students to get a better knowledge with the laboratory tools and techniques. This experiment taught me how to convert between SI units and standard American units of mass‚ length‚ temperature‚ volume and time as well as how to measure the units. Students become proficient in laboratory techniques such as measuring temperature and volume and calculating within them. Procedure:
Premium Volume Density Measurement
Lab II‚ Problem 3: Projectile Motion and Velocity Oct. 06‚ 2013 Physics 1301W‚ Professor: Hanany‚ TA: Vladimir Abstract A ball is tossed obliquely. The vectors of position and velocity are measured. The acceleration is calculated. Introduction A toy company is now making an instructional videotape on how to predict the position. Therefore‚ in order to make the prediction accurate‚ how the horizontal and vertical components of a ball’s position as it flies through the air should
Premium Velocity Euclidean geometry Analytic geometry
WIRELESS VIBRATION MEASUREMENT SYSTEM Vibrations are caused due to mechanical oscillation of a structure about an equilibrium point. There will be vibrations involved everywhere where there is any rotating system‚ mechanical system is involved. The vibrations involved at in these places will of high frequency. There will some places where the vibrations of lo0w frequency will be present which will also disturb the normal operation of the system or faultiness in the values measured by the system
Premium Electromagnetism Electricity Frequency
Collision Impulse and Momentum PH215L Physics 1 Lab Lab#8 Lab Was Held: 3/20/14 Report Submit: 3/27/14 Professor List Daniel Webster College Table Of Contents Introduction Theoretical background Equipment list Procedure Calculations and Results Discussion Conclusion Introduction In this lab we tested the duration of impact‚ the force of impact and the change of momentum of the particles involved in the collision all
Premium Classical mechanics Force Object-oriented programming
Cover page Course Code & Name: Engineering Science Title: Oscillations of a pendulum with a yielding support Instructor: Mr. Imran khan Cohort: Full Time Student Name & ID: Kyle Rigsby 68891 Date: 11/19/2014 Title page Oscillations of a pendulum with a yielding support Abstract Intent: The goal was to investigate the time taken for the pendulum to oscillate for a time period. Results: Table of Content Objectives i) Tie the end of a thread to a hole in the end of
Premium Clock Pendulum Orders of magnitude
Laboratory Report Cover Sheet DeVry University College of Engineering and Information Sciences Course Number: ECET110 Professor: Laboratory Number: 1 Laboratory Title: Analysis of a Series Circuit using Simulation and Actual Construction Submittal Date: 3/8/2014 Objectives: 1. To construct a series circuit and measure its equivalent resistance. 2. To predict and verify electrical characteristics of a series circuit using Ohm’s Law and Kirchhoff’s Voltage Law. 3. Determine
Premium Ohm's law Electric current Resistor
BioLab3 Lab Report 1 Measurement Student Name: I. Length Measurement EXERCISE 1 – Measuring length using the meter A dime and a meter stick have been used to determine the following: How thick is one dime? 1 mm How thick would a stack of ten dimes be? 10 mm How thick would a stack of one hundred dimes be? 100 mm How thick would a stack of one thousand dimes be? 1‚000 mm Determine the height of each of the following stacks of dimes in metric units. 10
Premium Kilogram Units of measurement Metric system
References: http://www.scribd.com/doc/94383213/Physics-Lab-Report Physics reference book ;pearson;James S.Walker http://www.digipac.ca/chemical/sigfigs/experimental_errors.htm
Premium Newton's laws of motion Mass Classical mechanics
PDP Physics Lab Report – 01 NAME: Wang Xueqian DATE: 2014/06/21 Introduction In this experiment‚ we will investigate the relationship between the linear speed of an object and magnitude of centripetal force acting on it. We will use a stopper moving in a circle to create an upward force on the hanging mass; at equilibrium‚ the upward force on the mass will exactly equal the centripetal force. Apparatus Two-hole Stopper Plastic Tube Plastic Clip Electronic balance Hooked Masses Stop Watch String
Premium Measurement Force Mass
Physics Lab Report Experiment M3 Centripetal Force School: La Salle College Class: 6G Group members (Group 7): Carson Ho‚ Tang Yui Hong‚ John Yu‚ Justin Kwong Date: 1 / 10 / 2014 Report is written by: Tang Yui Hong 6G (27) Title Centripetal Force Objective To verify the equation for centripetal force Apparatus Instrument Descriptions 1 rubber bung circular‚ cylinder screw nuts and wire hook / 1 small paper marker / 1 rule 1 metre safety goggles / adhesive
Premium Force Kinematics Experiment