Introduction. Friction was studied in this lab. The experiments were conducted using a clipboard glued to various surfaces with diffirentiating frictional properties. In order for us to test the varying Static friction or Kinetic friction we used a Newton force gauge‚ some wooden blocks‚ and a metal weight. The actual experiment consisted of two parts. The first part measured the net force‚ or more specific the net force required to overcome the kinetic friction coefficient‚ to move the block across
Premium
Conservation of Energy Lab Honors Physics December 9‚ 2014 Date Performed: December 5‚2014 Instructor: Mrs. Kelly I. Objective: Calculate the speed of the Bunny on release from the table II. Procedure: 1. Gather All Materials 2. Place the bunny turned in on itself on the ground (this enables the toy to launch itself upward by suction; elastic and potential energy). Do so 5 times 3. Measure the height traveled by the stopper using a meter stick per each trial. 4. Using the measurements
Premium Potential energy Energy Kinetic energy
Chemistry design: Fuel energy lab Research question: What is the energy density of cyclohexane‚ and how does it compare to the energy density of normal hexane? Variables: Independent variable – The independent variable in this experiment will be the type of fuel that will be used. This will be either Hexane or Cyclohexane. Each type will be given to us and labelled so it will be quite simple to control this variable. This cannot be measured using any apparatus so the lab assistant must be entrusted
Premium Heat Temperature Energy
Calorimetry Lab: Determining the Unknown Metal Purpose: To determine the identity of an unknown metal Hypothesis: The unknown metal is Copper Materials: * Safety glasses * Styrofoam cup * Thread or string * Glass rod * Thermometer * 100mL graduated cylinder * Hot plate * Balance * Unknown metal * 300mL beaker Procedure: i. Mass of metal was recorded ii. Water was heated on a hot plate in beaker iii. Temperature was recorded when water reached
Premium Heat Temperature Thermodynamics
Lab Report: Projectile MotionChange Launch Angle 03/05/2012 James Allison section 20362 Group 5 James Allison‚ Clint Rowe‚ & William Cochran Objective: In this lab we will compare different parameters of a launched projectile. This includes time of flight‚ initial velocity‚ initial vertical velocity‚ initial horizontal velocity‚ range‚ time of max height. All these data points are collected for 30°‚ 40°‚ 45°‚ 50°
Premium Range of a projectile Velocity Airport
Energy in food lab report Aim: How much energy there is in food. Hypothesis: If I work out how much the water temperature has risen by burning food underneath water‚ the mass of the water and the mass of food I can work out how much energy was in the food. Introduction: This experiment is about how much energy there is in food. There are a few different types of energy‚ the one we are looking at is chemical energy. Some other types of energy are: thermal energy which is heat‚ magnetic energy which
Premium Energy Thermodynamics Heat
blah i just want to be able to read this essay so I’m sorry if this isdissappointing to you hold on Physics Pre-AP Projectile Motion Lab Report Purpose The purpose of this lab was to determine how angle and gravity affects velocity and range. Procedure Materials Projectile launcher Marble Two measuring sticks Tin foil Pencil Procedure Set the angle of the projectile launcher to 30 degrees (make sure that the bottom of the launcher is even with the desk). Put the marble inside the
Premium Angle Archimedes Force
Introduction The purpose of this lab is to examine the motion of an electron‚ when it encounters a constant magnetic and electric field. We will also observe when the electric field and magnetic field will cancel each other out. This will lead to the electron having no net force acting upon it. By adjusting the values for the magnetic and electric fields‚ we will be able to check the different paths the electron follows. From this data we will be able to calculate the charge-to-mass ratio. Then
Premium Chemistry Electron Magnetic field
LAB WRITE- UP NAME: MANOUCHEKA FIDEL DATE: 9/19/14 TITLE: BACK AND FOURTH MOTION PURPOSE (Introduction): To qualitatively analyze the motion of objects that move back and forth. Then analyze and interpret back and forth motion in kinematics graphs. Use kinematic graphs to catalog objects that exhibit similar motion. PRELIMINARY QUESTIONS: Finding the average velocity Do any of the four objects listed above move in similar ways? If so
Premium Classical mechanics Velocity Newton's laws of motion
Name: Lab 201: Electric Field by Point Charges Section: 121A-H02 Date: February 8‚ 2012 Objective: To compute electric field and corresponding field lines caused by point charges using MATLAB. Theoretical Background: -electrons are negative‚ protons are positive -magnitude of force between A and B is: ‚ is 8.98755E9. -electric field is the region around a charged object -strength of electric field: = -electric field lines are used to visually show the field Procedure: Our
Premium Electric charge