LAB # 5 Relationship Between Drop Height and Diameter of Plasticine Sphere PROBLEM: A student suggest that there is a proportional relationship between height at which a plasticine sphere is dropped and the diameter of the flattened part after dropping. Design an experiment to determine if this suggestion is true or not. AIM: To investigate the relationship between the drop height and the flattened part of a plasticine sphere after being dropped. HYPOTHESIS: As the height of the sphere plasticine
Premium Measurement Circle
Muhammad Ali Jinnah University Islamabad Applied Physics Lab Project Report [ BRIDGE RECTIFIER] Group Members MIRZA UMAIR SAFDAR EE-123076 HAMZA BIN TARIQ EE-123086 Section PHY 7 Submitted To Ma’am Javeriah Iftikhar Abbasi Physics lab project Introduction: In this project we have created a device which takes input of 220 volts of ALTERNATING SOURCE and it gives us out put of 5 volts of DIRECT CURRENT for this purpose we have used various electronic components as
Premium Rectifier Alternating current Direct current
Experiment 1: Error‚ Uncertainties and Measurements Laboratory Report Jan Luke Mendoza‚ Alexis Vienne Munar‚ Paula Murakami‚ Giorla Joanne Negre Department of Math and Physics College of Science‚ University of Santo Tomas Espana‚ Manila Abstract Throughout the experiment the main goal is to find out about the realities in taking measurements‚ that is‚ that there will always be an uncertainty for each acquired value. And to find out and recognize these uncertainties was handled in the
Premium Measurement
Physics Waves Lab SL Introduction: This lab will investigate the properties of mechanical waves such as a longitudinal wave‚ focusing on the question: Does a change in the frequency of a wave result in a significant and convincing change in the speed of the wave? Hypothesis: Changing the frequency of the wave will not result in a change in speed because the wavelength will change proportionally as in theory. Student Designed Investigation Procedure/ Planning Procedure: 1. Three
Premium Measurement Light Electromagnetic radiation
Samantha Mackey 13. 2nd hour PHYSICS LAB REPORT: SPEED OF SOUND Purpose: In this lab‚ we will be doing 3 major things: 1) Collecting and organizing data to obtain resonant points in a closed pipe‚ 2) measure the length of a closed-pipe resonator‚ and 3) analyze the data to determine the speed of sound. Procedure: 1. Fill the graduated cylinder nearly to the top with water‚ with a tall glass tube open at both ends (the water level with act as the closed end). 2. Determine
Premium Sound Hertz Frequency
plate (reference 5) 6. Laboratory balance (reference 6) 7. Two kinds of metal Because of my illness I could not attend on this lab experiment. That is the reason why I do not have the discussion and the result for this experiment. Reference: Reference 1: Ruggiero‚ August. “LAB Manual for PHYSICS 102” at Essex County College Reference 2: physics. smu. edu Reference 3:
Premium Temperature Thermodynamics
Dalton Leach Physics 2 lab chapter 21 6/26/2015 Procedure Part I Wire Resistance: As wire length (cm) increases‚ the resistance (Ω) increases As wire area (cm2) increases‚ the resistance (Ω) decreases As wire resistivity (Ωcm) increases‚ the resistance (Ω) increases Procedure Part II: Ohm’s Law: Electricity‚ Magnets‚ and Circuits Ohm’s Law mA is milliamps‚ and 1000 milliamps equals one Ampere. Move the potential (volts) and resistance (ohms) sliders and observe the current (amps) As voltage
Premium Volt Incandescent light bulb Electric current
Kinetic Friction Experiment #13 Joe Solution E01234567 Partner- Jane Answers PHY 221 Lab Instructor- Nathaniel Franklin Wednesday‚ 11 AM-1 PM Lecture Instructor – Dr. Jacobs Abstract The purpose of this experiment was to examine kinetic friction and what factors affect it. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface affects friction. The surface area did not appear to affect friction‚ since there was a small percent difference
Premium Friction Force Classical mechanics
Name ___Sarah Carter___ Wire Resistance and Ohm’s Law Go to http://phet.colorado.edu/simulations/sims.php?sim=Ohms_Law and click on Run Now. Wire Resistance and Ohm’s Law Procedure Part I Wire Resistance: open the PhET Simulation Electricity‚ Magnets‚ and Circuits Resistance in a Wire. As wire length (cm) increases‚ the resistance (Ω) ___increases____ As wire area (cm2) increases‚ the resistance (Ω) ___decreases___ As wire resistivity (Ωcm) increases‚ the resistance (Ω) ____increases__
Premium Incandescent light bulb Volt Electric current
PDP Physics Lab Report – 01 NAME: Wang Xueqian DATE: 2014/06/21 Introduction In this experiment‚ we will investigate the relationship between the linear speed of an object and magnitude of centripetal force acting on it. We will use a stopper moving in a circle to create an upward force on the hanging mass; at equilibrium‚ the upward force on the mass will exactly equal the centripetal force. Apparatus Two-hole Stopper Plastic Tube Plastic Clip Electronic balance Hooked Masses Stop Watch String
Premium Measurement Force Mass