Charge gas through gas filters GT-F8102 and fill the system. This prevents dirty gas going to seals. • Always maintain barrier seal pressure @ 0.3to 0.5 atg on OTB side and TB side before start of the Lube oil Pump and during normal operation. • Open the suction valve HIC 8001 only after the system is filled with gas and reaching the suction pressure. • Open the discharge valve GTV 8002 before starting of compressor as seal gas to compressor is taken from downstream of the discharge
Premium Suction Liquid Pressure
The objective of this lab was to determine the relationship (if any)‚ between the pressure and volume of a gas given the temperature and # of molecules remained constant. Using the Boyle’s law apparatus‚ and textbooks to demonstrate pressure it was concluded that there was a relationship between pressure and volume. However‚ the relationship was not a direct relationship‚ and it was determined that the pressure and volume of a gas are inversely proportioned. Thus‚proving Boyle’s theory correct
Premium Gas Ideal gas law Gas laws
N) of another molecule. THERMAL ENERGY Thermal energy is the energy of a body arising from motion of its atoms or molecules. It is directly proportional to the temperature of the substance. THE GAS LAWS Boyle’s Law At constant temperature‚ the pressure of a fixed amount of gas is inversely proportional to its volume. P1V1 = P2V2 Each curve corresponds to a different constant temperature and is known
Free Gas Temperature Pressure
between the pressure and temperature of saturated steam in equilibrium with water. 2. To determine the vapour pressure curve. Introduction Properties of a fluid can change when heat and work are applied to it. There’s an interchange between the fluid and its surroundings when heat and work are applied according to the study of thermodynamics. Substances such as gases and vapors are often referred as P-V-T substances. Theory: An ideal gas obeys the equation of state that the pressure‚ specific
Free Pressure Ideal gas law Thermodynamics
46%______ 2. Calculate the partial pressures of the following gases at both atmospheric pressures: 760 mmHg 747 mmHg a. O2 __159.6mmHg_________ ____156.9mmHg_______ b. CO2 ___.3mmHg________ _____.3mmHg______ c. N2 ____597mmHg_______ ______587mmHg_____ d. H2O ___3.5mmHg________ _3.4mmHg__________ 3. What is the atmospheric pressure on the top of Mt. Whitney? __440mmHg_________ 4. Calculate the partial pressure of O2 on the top of Mt. Whitney
Premium Oxygen Gas Carbon dioxide
tappings required by the pressure sensors‚ additional tappings are included in the ducts to allow appropriate calibration instruments to be connected. The flow of air through the compressor is regulated by a throttle control device installed at the exit of the discharge duct. Rotation of the collar opens and closes a variable aperture which allows the head/flow produced by the compressor to be varied. NOMENCLATURE Variables Symbol | Term | Units | dpo | Pressure drop across the orifice plate
Premium Pressure Fluid dynamics Thermodynamics
retains a pressure that is constant between defining limits during both static and dynamic situations. In this context‚ ‘constant’ refers to maintaining a pressure that is continually within the margins of the drilling window. Typically within CBHP MPD operations‚ an automated system such as Weatherford’s Microflux Control system is used to measure and apply the required level of surface backpressure. The following describes the basic mathematics behind this system. [2] Well-bore pressure during
Premium Fluid dynamics Natural gas Petroleum
on the x-axis. Pressure (P1) and temperature (T1) on the y-axis Label all axes and provide a legend to identify each of the data series Provide the figure with a title in the lower box. Figure 1: The variation of pressure‚ P and Temperature‚ T with time‚ t. 2. The specific heat ratio of an ideal gas can be determined using the following formula: Where Ps is the starting pressure (before pressurising the vessel)‚ Pi is the intermediate pressure (stabilized once
Free Ideal gas law Thermodynamics Pressure
Boyle’s Law Experiment Aim To show that Pressure is proportional to the inverse to volume Method A gas syringe was attached to a pressure sensor. The pressure sensor was calibrated‚ assuming the atmospheric pressure at the time of the experiment was 100kPa. Differing volumes of gas were created in the gas syringe and they were recorded as were the corresponding values of pressure at that particular volume. The volume was varied between 20cm3 and 75cm3. Results A set of readings was obtained
Free Pressure Ideal gas law
of pure water in the data table. Letting the water boil will decrease the mass of the water present in the calorimeter. Note that the boiling point may be different than 100°C if the atmospheric pressure is not 760 Torr. The current atmospheric pressure for the day can be checked by selecting Pressure on the LED meter on the wall. 5. Drag the weigh paper to the calorimeter and add the NaCl. Wait 30 seconds for the salt to dissolve and then turn on the heater. When steam first appears
Premium Gas Pressure Temperature