EC1 VI-1 The results of experiment EC1 part V1 are summarized as below. V‚ I‚ Rm are directly measured Resistor A Resistor B Resistor C Resistor D V±ΔV(V) 6.748±0.001 7.759±0.001 9.061±0.001 10.383±0.001 I±ΔI(mA) 44±0.5 35±0.5 23±0.5 10±0.5 V/I±ΔR(Ω) 153.36±1.7 221.69±3.2 393.96±8.61 1038.30±52.02 Rm±ΔRm(Ω) 145.21±0.01 214.90±0.01 385.60±0.01 907.50±0.01 VI-2 (V‚ I) pairs for Resistor A using a DC power supply V-2 f = 0 Hz # V(Volts) I(mA) 1
Free Resistor Electrical resistance Series and parallel circuits
Introduction The purpose of this lab is to determine the percent mass of Cu in a penny and see if the fabricator that makes the planchets for the government is using the correct amounts of Cu in the pennies. The composition of a standard penny is 97.5% Zn and 2.5% Cu. In the lab we will be using Beer’s Law (A=elc+b where A is solution absorbance‚ e is a constant called molar absorbency‚ l is the length in cm‚ and c is the concentration). Using Beer’s Law in this lab a colorimeter is used to find the
Premium Chemistry Chemical element Copper
Lab report is one way we used during of after an experiment in a laboratory to subtly record and discuss the experiment. During a lab‚ we sometimes can observe only the physical part of the experiment‚ or may be some visible chemical changes. These changes indicate that the experiment we do is successful or not. However‚ in order to understand and achieve more from just simply doing the experiment‚ we write lab report to more profoundly understand the internal meanings of the experiment we do‚ and
Premium Critical thinking Thought
original state and the percent of the hydrate recovered was calculated by using the mass of the rehydrated sample by the mass of the original hydrate and then multiplied by 100%. Data Presentation & Analysis Table 1: The data was collected from the lab experiment. Sample calculations are shown. Mass of beaker with sample 30.765g Mass of empty beaker 30.263g Mass of sample .502g Mass of beaker with sample after 1st heat 30.661g Mass of beaker with sample after 2nd heat 30.657g Heating mass
Premium Mathematics Mole Heat
Lab 4 Part 1: 10 points Assignment: Create an Internet and E-mail Acceptable Use Policy Learning Objectives and Outcomes Research and compare Internet and e-mail use policies enforced by other organizations. Create an Internet OR e-mail use policy for an organization. Assignment Requirements You are a networking intern at Richman Investments. An employee of the company used employer-owned equipment to access the Internet and check his personal Web-based e-mail account. He followed a
Premium Internet E-mail Server
Density Lab Partners: Betty Alcaraz Date: 9/10/13 Teacher: Wright Class: 7th period Introduction/Purpose: To determine the densities of unknown substances. Pre-Lab: 1. Which is heavier‚ a pound of feathers or a pound of lead? a. A pound of lead. 2. What is the density of a mineral if 427 g of the mineral occupy a volume of 35.0cm3? b. 12.2g/cm3 3. The water level in a graduated cylinder stands at 20.0 mL before and at 26.2 mL after a 16.74 g metal sample
Premium Volume Density Mass
Jeanine Campa Biology 101 10/20/2010 Ecology-Interspecific Interactions Lab Intro: Ecology is the study of how organisms interact within their environment. Every species interacts with its surroundings‚ whether it’s within their populations‚ community‚ ecosystem‚ etc. In this lab‚ we will be comparing two different species and how they grow alone as well as together‚ in the same environment. More specifically‚ in this lab‚ we will be dealing with one of the most important ideas in ecology‚ the
Premium Species Ecology Competition
Collision Lab Simulation Purpose: To study elastic and inelastic collisions in one-dimension. Background Information: Momentum: is a measure of mass in motion. It is the product of mass x velocity. Conservation of Momentum: in the absence of external forces‚ such as friction‚ the linear momentum of a system remains constant. Procedure: 1. Open web browser and go to the site: http://phet.colorado.edu 2. Click “play with sims”‚ then “physics”‚ and then “motion” 3. Find the “Collision Lab” 4
Premium Classical mechanics Inelastic collision Kinetic energy
ITT Technical Institute - Print 1 of 30 http://itt.coursesmart.com/print?__displaygrbooks=1&xmlid=97812692... User name: Eidson Jr‚ Jerry Eidson Jr‚ Jerry Book: Introduction to Networking Lab Manual Page: 2. No part of any book may be reproduced or transmitted by any means without the publisher’s prior permission. Use (other than qualified fair use) in violation of the law or Terms of Service is prohibited. Violators will be prosecuted to the full extent of the law. 9/20/2014 11:21 AM ITT Technical
Premium Vocational education User
In each station there was a positive and a negative control. If the substance was the same as the negative control then it was negative. If the substance was the same as the positive control than the substance is positive. In the first lab we did the Paper Spot test‚ one would have had to apply the substance on a cardboard like paper. If it looked oily it was the biomolecule called lipid. The result of test one was it stayed the same‚ it did not turn oily and was clear. Next was the test
Premium DNA Metabolism Protein