Finding the Activation Energy of the reaction between Hydrochloric Acid and Sodium Thiosulfate The equation for the reaction is: S2O32- (aq) + 2H+(aq) ⋄ SO2 (g) + S(s) + H2O (l) Equipment - 2 boiling tubes - 400 cm3 beakers - Marker pen - Stand and clamp - Timer - Bunsen burner‚ tripod and gauze - 0 – 100 oC thermometer - 2 x 10 cm3 measuring cylinders - Access to a fume cupboard. Method 1. Label two boiling tubes A and B. Mark a dark spot on the side of a 400cm3 beaker‚ then ½ fill
Premium Temperature Measurement Energy
DISCUSSION: The results obtained based off trials one‚ two‚ and three would support the initial rationale hypothesis that if salt concentration is not equal to the optimum concentration of 0.15M‚ then its ability to function will decrease. 0.15M with the trypsin added had the lowest absorbency compared to the three other concentrated groups that were tested (0.0M‚ 0.075M‚ 0.30M). Closer comparison that if you take the results obtained from trial one with trypsin at a salt concentration of 0.075M
Premium Chemistry Concentration Solution
Hydroxide (NaOH) by titrating it with Hydrochloric Acid (HCl) and to identify any possible sources of error. A colour change from pink to yellow signified the end of each individual titre as the NaOH had been neutralised. Experimental: Method: Firstly two solutions were prepared to show the colour of the Phenol Red indicator in acid and alkaline conditions. These colours were then used to determine the end point of each titre. In the experiment 0.100M HCl (acid) was added‚ from a burette‚ to a solution
Premium Sodium hydroxide Chemistry Base
Investigation How does the concentration of the sodium thiosulfate affect the rate of reaction to hydrochloric acid? contents page 1: contents‚ aim‚ prediction‚ equation‚ diagram page 2: equipment‚ preliminary experiments page 3: page 4: page 5: page 6: page 7: page 8: Aim: In my investigation I am trying to find out how the rate of reaction between sodium thiosulfate and hydrochloric acid gets affected but the concentration of the thiosulfate. Prediction: My prediction is that the increased
Premium Chemical reaction Reaction rate Chemistry
then I will see the temperature slope increase in the reaction with an increased concentration because with an increase of moles‚ the particles will be colliding more often‚ therefore increasing the probability that the proper energy and alignment will occur to create more collisions in the same amount of time. Methods: List of Materials: • 110 mL of NaOH at 1 M (10 mL per run) • 110 mL of NaOH at 0.5 M (10 mL per run) • 220 mL of Acetic Acid at 50% (10 mL per run). • Vernier Temperature Probe.
Premium Chemical reaction Chemistry Sodium hydroxide
calculated products are determined using the limiting reagent‚ (the substance that runs out first which stops the reaction) and are called the theoretical yield. The theoretical yield is the amount of product that should be acquired during the experiment if all aspects go perfectly. However‚ due to experimental errors‚ very few labs do so. These results are called actual yield. The percent ratio between the theoretical and actual yield is called the percentage yield. It is calculated by taking the actual yield
Premium Chemistry Stoichiometry Yield
the amperage is generated from flows of electrons between the two metals in the metal sulfate solution of the electrolyte. In order for a chemical reaction to take place‚ the reactants must collide. The collision between the molecules in a chemical reaction provides the kinetic energy needed to break the necessary bonds so that new bonds can be formed. Thus‚ increasing the concentration of the anode‚ zinc sulfate‚ will increases the rate of reaction for oxidation because there are more zinc ions in
Premium Electrochemistry Electrolysis Battery
Factors affecting the rate of reaction between a metal and an acid The rate of a reaction can be measured by the rate at which a reactant is used up‚ or the rate at which a product is formed. The temperature‚ concentration‚ pressure of reacting gases‚ surface area of reacting solids‚ and the use of catalysts‚ are all factors which affect the rate of a reaction. Individual properties of substances also affect reaction rates. The scope of these properties is broad and there are few generalizations
Premium Oxygen Chemical reaction Base
31 Introduction- Magnesium is a silvery-white alkaline metal found represent by the atomic number of 12. This experiment involves combining Magnesium with Oxygen which is a gas represented by the chemical element 8. The word equation for the result of this experiment is Magnesium + Oxygen= Magnesium Oxide. The equation is Mg + O =MgO Definitions Word Definitions Mass Number The Mass number is the amount of Protons and Neutrons in the Nucleus. Atomic Number The amount of protons found
Premium Chemical element Chemistry Oxygen
react with hydrochloric acid; and 1 cm3 of element X has a mass of 1.8 grams. Is element X a metal or non-metal? Give the reasons for your answer. Element X is most likely a typical non-metal. First of all‚ element X melts in boiling water; non-metals typically have low melting and boiling points. Furthermore‚ element X is unable to react with hydrochloric acid. This greatly indicates that element X is a non-metal as most non-metals fail to react with hydrochloric or dilute acids. In order
Premium Chemical element Copper Aluminium