Recrystallization and Melting Point of Benzoic Acid Organic Chemistry 1 10/4/12 Abstract Recrystallization was done to remove impurities from the sample. The percent recovery of benzoic acid during recrystallization is 23.02%. The difference between the pure and impure samples was observed by comparison of melting points. It was found that impure sample had a lower and wider melting point range of 120.1-122.2 (C). The pure sample melting point range was 121.3-122.5 (C). These ranges helped determine
Premium Solubility
Solids: Recrystallization and Melting Points Reference: Chapter 3. Solids: Recrystallization and Melting Points. Read pages 93-94 and 113-117. Experimental procedure‚ pages 118-119. Parts 1-3. Part 1: Melting points of Urea and Cinnamic Acid. Part 2: Melting point of unknown. Part 3: Melting point of Mixture- Urea and Cinnamic Acid (take melting points of mixtures in 1:4‚ 1:1 and 4:1 ratios). Reactions Main Reaction: Not a chemical reaction but a physical reaction. Urea in solid mixed with
Premium Chemical substance Temperature Mixture
Melting Points Elizabeth McGrail Organic Chemistry I 25 January 2013 ABSTRACT The objectives of this lab are‚ as follows; to understand what occurs at the molecular level when a substance melts; to understand the primary purpose of melting point data; to demonstrate the technique for obtaining the melting point of an organic substance; and to explain the effect of impurities on the melting point of a substance. Through the experimentation of three substances‚ tetracosane‚ 1-tetradecanol and
Premium Chemistry Molecule Temperature
Results My unknown sample was number 18. I did three melting point trials‚ which resulted in a melting point range of approximately 120°C to 122°C‚ as shown in Table 1. I also did two mixed melting point trials using Benzoic Acid and Succinimide‚ as shown in Table 2. Percent recovery is 28.26 grams. Table 1: Unknown Melting Point Trials Trial Melting Point 1 120°C – 122°C 2 120°C – 122°C 3 119°C - 122°C Table 2: Mixed Melting Point Trials Trial Benzoic Acid MP Unknown #18 MP Succinimide
Free Chemistry Chemical substance Benzene
Introduction: The technique used in this experiment is recrystallization. Recrystallization is an often-used method for purifying solids. Recrystallization works by taking advantage of the different solubility properties of compounds‚ and allows impurities to be removed from crude solids. Performing a recrystallization is usually a straightforward task. First‚ you add a small amount of solvent to the impure compound in a flask‚ and heat the contents until all the material has dissolved. Then‚ you
Premium Aspirin Acetic acid Paracetamol
Experiment 1: Recrystallization – Evaluation Summary Last Name: Xavier First Name: Jessica Date: October 1st 2013 Lab Day/TA/Group: Wednesday(1:35pm)/Group A Labs reports must be typed and chemical structures must be drawn with ChemDraw. Report must not exceed three pages (including this page). Page limit does not include any attached spectra or references. ** Deductions for hand written report/structures and exceeding page limit ** Report Breakdown Data/Results: _________________
Premium Temperature
Introduction Recrystallization is a method used to purify solid organic compounds. Using the recrystallization technique‚ a solid compound is dissolved in a solvent and the compound slowly crystallizes as the solution cools. Using a filtration technique‚ a pure solid is produced when the molecules of the impure particles in the compound are excluded from the crystal lattice. After obtaining the pure compound‚ a melting point determination procedure can be done using a mel-temp device to correctly
Premium Solubility Solid Chemistry
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
repCHEMISTRY I - LABORATORY EXERCISE MANUAL LABORATORY EXERCISE 10: Melting Point and Boiling Point Determination This is a traditional lab. You’ll simply follow the step-by-step procedure‚ keeping records of your measurements and observations. Each student will write their own lab report‚ which should include the following: Name: Names of lab partners: Date of Experiment: Date Report Submitted TITLE: Purpose: A brief statement about what the experiment is designed to determine
Premium Liquid Temperature Water
The objective of this experiment was to learn the process of recrystallization and how this process removes the impurities from a pure solid compound. The methods used to achieve this objective were also hot vacuum filtration in order to remove suspended solid impurities‚ and isolating the pure acetanilide. In the next lab‚ percent recovered was obtained through weighing the acetanilide sample as well as comparing its melting point range. In this experiment‚ the sample‚ acetanilide was weighted
Premium Water Solvent Chemistry