Melting Point Determination and Thermometer Calibration Lab Background: The melting point of a substance‚ a solid in this case‚ signifies the temperature at which the first crystal starts to melt until the temperature at which the last crystal disappears is reached. That being said‚ melting points are expressed in ranges‚ am organic compound will have a sharp range depending on the purity of the compound. Impurity of an organic substance will register an abnormal melting point based on its
Premium Salicylic acid Temperature Chemical compound
Chem 231: Organic Chemistry Lab EXPERIMENT #2 and #3 Extraction and Evaporation Recrystallization and Melting Point Measurement PURPOSE: 1. To the components of a simulated pharmaceutical preparation‚ Panacetin‚ and identifying the unknown component of the mixture through extraction and separation methods. 2. To learn how to purify by recrystallization‚ how to dry them and how to obtain a melting point. PRECAUTION: ACETANILIDE AND PHENACETIN ARE EYE AND SKIN IRRITANTS. Minimize
Premium Chemistry
Experiment 2&3 Recrystallization and Melting Points Determinantion of Benzoic Acid Abstract In experiment 2‚ recrystallization was used to purify the crude benzoic acid extracted from a mixture during experiment 1. Then a percent recovery for this recrystallization process was calculated. In experiment 3‚ the melting point ranges of the crude and purified benzoic acid were both determined by using Melt Temp Apparatus. Introduction Recrystallization is a purification technique for non-volatile
Premium Chemistry Liquid Water
Title: Recrystallization of Pure Phthalic Acid‚ Naphthalene‚ and Anthracene Introduction Recrystallization is a method used for purifying solid organic compounds. It is the most efficient method to purify and remove impurities from a solid to allow a crystal to grow. The method is when the solute in a hot solvent yields to a solution. Once the solvent cools‚ the solution is saturated with respect to the solute‚ which is when it recrystallizes. A crystal is the end result of the method and it is a
Premium Solubility Solution Chemistry
The experimental melting point range of the desired alkene product‚ trans-9-(2-phenylethenyl) anthracene‚ was found to be 132-134 ˚C‚ in comparison to the literature value melting point range of 130-132˚C‚1 it was slightly higher than expected. Overall‚ the experimental melting point range varied from the initial melting point temperature and maximum melting point temperature by 2˚C. As the experimental melting point had a small range of temperature variance and was above that of the literature value
Premium Melting point Temperature Liquid
steps during this recrystallization lab in order to achieve the desired results‚ which included heating the solvent‚ completing a hot filtration‚ completing a vacuum filtration of a chilled solution‚ as well as drying and calculating the weight and melting point of the final version of the sample. I began the lab with 1.5 grams of the impure acetanilide solute and ended the lab with 0.05 grams of pure acetanilide crystals. The percentage of pure acetanilide I recovered during this lab was 3.33%‚ which
Premium Ethanol Liquid Solvent
Determine the melting points of two organic compounds known to have the same melting range when pure. b) Determine the mixture melting point of a mixture of the two pure compounds. c) Identify an unknown organic compound by determining its melting point and mixture melting point. Procedure and Observations: Using the procedure outlined in Appendix A of the Lab Manual‚ approximately equal samples of p-Nitrophenol and acetanilide‚ which are known to have the same melting range of 113-114
Premium Chemical compound Chemical substance Temperature
and then compare its melt point to the two other possible substances. Theory Panacetin should be made up of about 50 percent of the unknown component that we previously separated out of Panacetin for testing. We suspect that this unknown compound is either acetanilide or phenacetin. From the solubility of acetaminophen and phenacetin‚ we could know both of them are relatively soluble in boiling water but insoluble in cold water so that we took the recrystallization as the method to purifying
Premium Solubility Chemical substance Temperature
Introduction The purpose of the experiment was to determine the melting points of compounds using a Mel-Temp device. The melting point of naphthalene‚ urea‚ and sulfanilamide are found. This is then followed by the measuring of an unknown compound‚ and an impure sample (a small amount of naphthalene mixed with the unknown). Experiment In the lab‚ the height of the chemical in the capillary was set to 2-3 mm thickness. The voltage at the Mel-Temp started at a low setting of 1.5-2. The heat was
Premium Temperature
Mixture Melting Points Abstraction Determining the melting point is very significant in order to identify an unknown. In this experiment‚ measuring the melting point was done by using melting point apparatus. The melting point of the unknown sample #10 was 111.5˚C. There were two possible compounds which were dibenzoyl ethylene and o-Toluic acid because their melting points were 111.2˚C and 109.8˚C when each compound was mixed with the unknown. Therefore‚ the unknown #10 was dibenzoyl ethylene
Premium Chemical compound Chemistry Melting point