Unit 4 Assessment 2-Benzoic Acid Synthesis Synthesis and Investigation of Benzoic Acid Our aims: Create benzoic acid using benzaldehyde and hydrogen peroxide. Then remove some impurities from the benzoic acid crystals. Apparatus: Titration Pipette (25 cm3) Burette (50 cm3) Retort stand Clamp Conical flask (250 cm3) Volumetric flask (250 cm3) and stopper White tile Beakers (250 cm3) Dropping pipette Filter funnel Deionised water Phenolphthalein indicator Volumetric flask
Premium Chemistry Water Sodium hydroxide
SEGi University Extraction of Benzoic Acid by Balvinder Singh (SCM 015 677) Lab Partners: 1) Surrean Rao 2) Wong Kai Jun 3) Kanaga Luckshimi 4) Sasiskala Regal ECE2332 Chemical Engineering Practices Submitted: 1st October 2013 Supervisor: Mr Ayman William 1.0 Abstract /summary The purpose of this experiment to carry out in the lab is because to determined the capability to water droplet to carry out the liquid-liquid extraction. The studies is to determine
Premium Concentration Liquid Chemistry
Forming Methyl Orange an Azo Die Abstract: An synthetic azo dye was created by reaction of diazonium salt with N‚N-Dimethylanaline. The final product created was 4-dimethylaminoazobenzene-4-sulfonic acid‚ an orange clay-like substance. Sulfanilic acid was chemically manipulated by using sodium carbonate followed by cooled sodium nitrate and hydrochloric acid to form the diazonium salt used in the reaction. The products were washed in ethanol. The product was obtained at an 84% yield and was
Premium Chemistry Hydrogen Chemical reaction
The obtained mass of benzocaine and benzoic acid mixture was measured to be 2.075 grams. Following being dried for a week the mass of benzocaine was recorded to be 0.250 grams‚ and benzoic acid was recorded to be 0.600 grams. The melting point range of benzocaine was measured to be 89.5°C-91.5°C‚ while benzoic acid’s melting point range was measured to be 129°C-131.3°C. The percent mass recovered was calculated to be 40.96% for the experiment. Table 1 illustrates the collected information. Starting
Premium Chemistry Oxygen Solvent
salicylic acid (Hint: You should use your empirical data to support your claim). -The Salicylic acid that I obtained had a melting point range around 157-158 degrees Celsius for Part A. For Part B the melting point range was 156-157.5 degree Celsius. Part B‚ I would say the sample is less pure because of the notion that impurities lower the melting point. Since part A ‘s melting point was higher and closer to the melting point of the pure sample‚ it was more pure. The pure Salicylic acid that I got
Premium Temperature Purity Celsius
Adjei 3809009 INTRODUCTION Recrystallization is a method of purifying a solid. There are two types of impurities: those more soluble in a given solvent than the main component and those less soluble. (If there are any impurities that have the same solubility as the main component‚ then a different solvent needs to be chosen.) When organic substances are synthesized in the laboratory or isolated from plants‚ they will obviously contain impurities. Several techniques
Premium Solubility Temperature Crystal
TWO-BASE EXTRACTION OF BENZOIC ACID‚ 2-NAPHTHOL‚ AND NAPHTHALENE FROM UNKNOWN SAMPLE # 131 Douglas G. Balmer (T.A. Mike Hall) Dr. Dailey Submitted 11 July 2007 Introduction: The purpose of this experiment was to separate a sample of benzoic acid‚ 2- naphthol‚ and naphthalene of unknown proportions using a two-base extraction method. The three components of the mixture will react differently to sodium bicarbonate and sodium hydroxide because each of the bases’ conjugate acids has a different pKa
Premium Sodium hydroxide Hydrochloric acid PH
Acid-Base Extraction: Separation of an Organic Acid‚ Base and a Neural Compound Introduction/Background Acid base extraction is a widely used commercial method in separating acids‚ bases and neutral compounds. This is concept is based on several physical properties of the compounds‚ such as boiling point‚ melting points and solubility. The different solubility properties of the protonated and non-protonated forms of these compounds depend on the functional groups present‚ such
Free Acid Chemistry Carboxylic acid
De-esterification for Synthesis of Benzoic Acid BATCH REACTOR Shane Bulk Chris Crosley David McGuire Max Skula Yunjing Song Shriram Sundarraj Nelson Zhou 155:416 Process Laboratory II Professor Jerry Sheinbeim January 28 – February 28‚ 2014 ABSTRACT The observed reaction that took place in this experiment was the de-esterification of ethyl benzoate to form benzoic acid. This experiment was used to determine the rate constant k of the synthesis of benzoic acid at different temperatures
Premium Chemical kinetics Sodium hydroxide Ethanol
Recrystallization and Melting Point of Benzoic Acid Organic Chemistry 1 10/4/12 Abstract Recrystallization was done to remove impurities from the sample. The percent recovery of benzoic acid during recrystallization is 23.02%. The difference between the pure and impure samples was observed by comparison of melting points. It was found that impure sample had a lower and wider melting point range of 120.1-122.2 (C). The pure sample melting point range was 121.3-122.5 (C). These ranges helped determine
Premium Solubility