Faculty of Engineering and Technology (FET) PPH 0125 Mechanics Foundation in Engineering ONLINE NOTES Chapter 1 Physical Quantities Faculty of Engineering and Technology‚ Multimedia University‚ Jalan Ayer Keroh Lama‚ Bukit Beruang‚ 75450 Melaka‚ Malaysia. PPH0125 MECHANICS Contents 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Introduction to SI Units. Basic Quantities Derived Quantities Conversion of Units Scalar and Vector Quantity Factor of ten Simplification (Standard Prefixes) Dimension:
Premium Units of measurement Physical quantity Dimensional analysis
PEES 4200W- Physiology of Exercise Lab #2: Metabolism and Energy Expenditure 1. The Respiratory exchange ratio is the ratio of the volume of carbon dioxide produced and oxygen consumed. The ratio indicates the energy that the subject is expending for indirect calorimetry‚ how efficient the subject ’s body is at utilizing the oxygen inhaled‚ as well as the main substrate being used for energy during varying intensities of exercise. During rest the volume of carbon dioxide was 0.73L/min‚ the volume
Premium Oxygen Carbon dioxide Ratio
Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
Mechanics experiment 2 : (GROUP 3) Student no or trials Mass m(g) Deviation m-m ave (g) Absolute Deviation m-m ave (g) 1 75.5 0 0 2 75.3 -.02 0.2 3 75.8 .3 .3 4 75.4 -.10 .1 5 75.5 0 0 Sum 377.5 0.6 Average 75.5 0.12 Table 1: Measurement of the old balance Table 2 : Measurement for the new balance Student no or trials Mass m(g) Deviation m-m ave (g) Absolute Deviation m-m ave (g) 1 74.1 -1.14 1.14 2 75.5 .26 .26 3 75.4 .16 .16 4 75.6 .36 .36 5 75.6 .36 .36
Premium Length Volume 175
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
Summary There are two parts in this experiment where we shall observe the mechanics of fluid flow in a closed conduit and also to find out the characteristics of a centrifugal pump. In the first part‚ we applied the principle of pressure difference across fittings in a closed conduit to find out the loss coefficients of these fittings. Thereafter‚ we determine the individual flow rates of the 3 different lines in the system. With this knowledge‚ sufficient understanding about the properties and
Premium Fluid dynamics
LAB REPORT Introduction: In a chemical change‚ the identities of substances change and new substances form. In an equation the substances on the left are the reactants. The substances on the right are the products. In this experiment the objectives are to observe evidence that a chemical change has taken place. Infer from observations that a new substance has been formed. Identify and record observations that show energy is involved in chemical change observe the color‚ solubility of some substances
Premium Chemical reaction Chemistry Hydrogen
Lab Report: Stoichiometry Lab Oct. 27‚ 2011 Claire Elizabeth Lab Partners: Hannah Signature:___________________ Introduction- Baking soda and vinegar are two common materials found in almost every household. That‚ plus the fact that all the starting and finishing materials are non hazardous and safe‚ is why this is one of the first chemical reactions that many people are exposed to The purpose of this experiment tests which of the two reactants (vinegar and baking soda) is the limited
Premium Sodium bicarbonate Acetic acid Measurement