Specific Heat of a Metal Post-Lab I. Purpose The purpose of this lab is to determine the specific heat of an unknown metal. II. Safety Wear goggles and lab apron at all times. Use caution when boiling water. Do not pick up hot beaker or hot metal with hands. Use tongs. III. Pre-Lab Questions 1. A 12.5 g metal is raised to 100C in boiling water. It is put into 82.8 g of water at 22.4C‚ and the water rises to 28.6C. Recalling that the specific heat of water is 4.18J/gC‚ use the equation above
Premium Water Temperature Heat
Density of Metals Problem: How does the mass and volume help determine the density of known metal samples? Hypothesis: When comparing the density of Zn(zinc) and Cu(copper)‚ you will find that Copper is more dense than Zinc. You can test this out by using the density formula D=m/v. Materials: * 2 metals (options: zn‚ al‚ or cu) * 3 samples of each metal (small‚ medium‚ and large) * Scale/Balance * Calculator * Water * Graduated Cylinder Safety: * Be prepared for your
Premium Density Volume Mass
Production and Properties of Metals Mr J E Chuter‚ Cert Ed 2012 En No 20100292 Introduction I have decided to produce a project based on the production and properties of metals‚ as although I have worked as a welder for over 30 years‚ and a welding teacher for the last 2 years on apart-time basis‚ I felt I didn’t know enough information on the material that I work on‚ on a daily
Premium Iron Steel Zinc
Experiments with Metals and Ions of Metals Introduction Metals are similar in their physical properties in general‚ but they are not identical. Most of the metals are solids; few of them are liquids‚ such as mercury and cesium. Density of metals is not similar also. For example‚ sodium has density of 0.97g/cm3 while lead has density of 11.4g/cm3. Melting point of sodium is 98.0oC while for lead it is 327.6oC. Metals have the capability to lose electrons when they react with non-metals such as
Premium Chemical element Chemistry Hydrogen
– P25 (P10 — P35) CVD-coated carbide grade for finishing to roughing of steel and steel castings. The combination of a wear resistant coating and a tough substrate allows the grade to handle continuous cuts as well as interrupted cuts at high metal removal rates. GC1525 (HC) – P15 (P05 — P25) A PVD coated cermet with very high wear resistance and good edge toughness. For finishing and semi-finishing of low carbon and low alloyed steels. To be used when good surface quality is demanded at
Premium Steel Carbon
Metals and Halogens reactions Elements such as fluorine‚ chlorine‚ bromine‚ iodine‚ and astatine belong to Group 7‚ Halogens. At room temperature‚ fluorine is a yellow gas‚ chlorine is a pale green gas‚ bromine is a red liquid‚ and iodine is a purple solid. Astatine is a radioactive element‚ therefore it exists only in small amounts. All the halogens exist in diatomic molecules. They have high ionization energies and are the most electronegative elements. Their electron configuration ns2 np5 make
Premium Chlorine Sodium chloride Periodic table
WEF_Metals and Mining Scenarios 15.1.2010 17:32 Page 1 Mining & Metals Scenarios to 2030 WORLD ECONOMIC FORUM in collaboration with the INTERNATIONAL FINANCE CORPORATION and MCKINSEY & COMPANY WEF_Metals and Mining Scenarios 15.1.2010 17:32 Page 2 Description Green Trade Alliance Rebased Globalism Resource Security Geo-economic landscape In 2030‚ the world is divided and countries are defined economically by whether or not they belong to the Green Trade Alliance (GTA)‚ formed in
Premium Economic growth Strategic management Economics
Cumberland Metal Industries: Engineered Products Division‚ 1980 October 21‚ 2013 CA by Yiwen Zhang Cumberland Metal Industries (CMI) is one of the largest metal manufacturers in the world. The company evolved from selling metal as a finished product to one that used it as a raw material‚ increasing sales from $250‚000 in 1963 to over $18‚500‚000 in 1979. Currently‚ CMI relies heavily on SlipSeal‚ which is used as a high-temperature sealant in automobiles. Although CMI dominates
Premium Price Pricing Costs
I. BACKGROUND CMI has developed a new technology using curled metal to create pile driving pads. Compared to existing products on the market‚ these pad offer several benefits: • Faster pile driving saves contractors rental fees‚ labor expense ‚ and spreads overhead over more feet driven in a given period of time • Longer life of pads save contractors additional cost in reducing changeover time • Heat resistance further reduces changeover time‚ saving additional expenses • Safety – CMI pads
Premium Microeconomics Economics Time
Cumberland Metal Industry 1‚2- The first two questions will be gone through together in order to avoid confusion. Pricing is one of the most important elements to launch a product on the market. Mainly‚ because it is the only element‚ together with the marketing mix‚ that produces revenues. It is fundamental to set the right strategy in deciding and setting the price of a certain product to be sure that is fully understood and appreciated by customers in all its aspects and characteristics. A
Premium Pricing