Timeaccording to the no. of the boards | | Setup | Run | 8 | 40 | 120 | 800 | PREPARATION | | | | | | | Artwork Generation | 29 | 0.000 | 29.0 | 29.0 | 29.0 | 29.0 | Inspect & Sheer | 20 | 0.500 | 20.5 | 22.5 | 27.5 | 70.0 | Punch Tooling Holes | 10 | 0.500 | 10.5 | 12.5 | 17.5 | 60.0 | IMAGE TRANSFER | | |
Premium Quality control Drill Quality assurance
Quick Changeover (SMED) As lean production is dependent upon small lot sizes‚ small lot sizes are dependent upon quick changeovers. If set-ups or changeovers are lengthy‚ it is mathematically impossible to run small lots of parts with low inventory because large in-process inventories must be maintained to feed production during changeovers. For example‚ large stamping dies commonly took hours to change until the development of quick die change methods (Single Minute Exchange of Die‚ or SMED).
Premium Theory of Constraints Bottleneck Improve
Comau Robotics Presentation February 2012 Property of Comau S.p.A. - Duplication prohibited Presentation Index Comau Robotics Business Line Strategy Robots & Control Unit Standard Solutions Aftermarket Property of Comau S.p.A. - Duplication prohibited February 2012 2 Presentation Index Comau Robotics Business Line Strategy Robots & Control Unit Standard Solutions Aftermarket Property of Comau S.p.A. - Duplication prohibited February 2012 3 Comau Robotics Robotics Head quarter Via
Premium Robot Robotics Welding
CALIFORNIA SYSTEMS CORPORATION (CSC) Executive Summary: Since CSC has decided to broaden its reach by entering the personal computing industry and made a strategic decision to outsource the DVD drives due to the manufacturing costs involved‚ it needs to decide on the sourcing strategy and select a supplier which would optimize its cost over the long run and result in profits for the company. On the basis of the suppliers considered‚ an evaluation scorecard has been formed which would rate the
Premium Financial ratios Financial ratio Variable cost
property resulting from a fiber structure is obtained. (v) The strength and hardness decreases at elevated temperature DISADVANTAGES OF HOT WORKING PROCESSES Disadvantages of hot working process (i) The life of the tools used is less. (ii) Tooling and handling costs are high. (iii) Close tolerances cannot be maintained‚ oxide films are surface characteristics. a: Rolling. HOT ROLLING Rolling is a fabricating process in which the metal‚ plastic‚ paper‚ glass‚ etc. is passed through a
Premium
Chapter 4 Extrusion Subjects of interest • Introduction/objectives • Classification of extrusion processes • Extrusion equipment (Presses‚ dies and tools) • Hot extrusion • Deformation‚ lubrication‚ and defects in extrusion • Analysis of the extrusion process • Cold extrusion and cold-forming • Hydrostatic extrusion • Extrusion of tubing • Production of seamless pipe and tubing Suranaree University of Technology Tapany Udomphol Jan-Mar 2007 Objective • This chapter aims to provide
Premium
INSTITUTIONAL TRAINING REPORT Done at ROOTS INDUSTRIES LIMITED COIMBATORE. Submitted in partial fulfillment of the requirement submitted for the award of the degree of B.Com(CA) Bharathiyar University‚ Coimbatore. By JAYADEV.J Reg.No : 042AC2076 Under the guidance of Mrs.USHA‚ M.Com.‚ M.Phil.‚ PGDCA.‚ Department of Commerce with Computer Applications SMS COLLEGE OF ARTS & SCIENCE ( Affiliated to Bharathiyar University ) Coimbatore – 641 010. CERTIFICATE This is to certify that this
Premium Hydraulics Industry Manufacturing
available components is one aspect. The amortization of fixed set-up or tooling costs over the production run for a forging or casting application is another. The most widely accepted cost-estimating tool for adjusting cost to volume is the learning curve. This assumes that repetitive production costs will decrease due to learning by the manufacturing staff - by increasing yields‚ increasing operation throughput‚ improved tooling‚ and substituting equipment for labor‚ eliminating unnecessary steps‚
Premium Learning curve Cost
Executive Summary De Havilland is a Canadian aviation company that is in the process of determining how to contract out the supply of its flap shrouds and equipment bay doors for its Dash 8 aircraft. Its current supplier‚ Dollard Plastics is believed to be charging a large premium over market price and for that reason‚ a completive tender was issued to test De Havilland’s hypothesis. After receiving bids from 9 companies‚ a strategic review of De Havilland’s options and alternatives was conducted
Premium Management Marketing Balance sheet
forming is performed on a stretch press‚ in which a piece of sheet metal is securely gripped along its edges by gripping jaws. The gripping jaws are each attached to a carriage that is pulled by pneumatic or hydraulic force to stretch the sheet. The tooling used in this process is a stretch form block‚ called a form die‚ which is a solid contoured piece against which the sheet metal will be pressed. The most common stretch presses are oriented vertically‚ in which the form die rests on a press table
Premium Yield Aluminium Drawing