Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
Abstract This lab’s purpose was to test the patterns of percolation in various places. This lab tested how soil would absorb water based on different places. Distance from a group of trees‚ distance from a swamp‚ and different types of soil were tested. From the results collected‚ you can not prove‚ but you can infer that the ability to absorb increases as you go farther away from a swamp‚ and a group of trees. The ability to absorb also increases based on how much silt is in soil. Introduction
Premium Soil Surface runoff Digestion
Acid Base Titration Purpose: The purpose is to calculate the molarity of a NaOH solution by titrating the base with 5mL of standard HCl solution in each trial. By adding the base with unknown molarity to the acid with 0.10M the molarity of NaOH can be calculated. The base‚ NaOH‚ helps bring the pH of the acid‚ HCl‚ closer to seven‚ which neutralizes it. When using the buret the amount of NaOH used is able to be determined. Then by writing a balanced chemical equation and using the titration
Premium Titration Sodium hydroxide Acid
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
various forms‚ such as marble‚ chalk and coral. It is produced either as powdered or precipitated calcium carbonate. Calcium carbonate decomposes to calcium oxide and CO2 on heating. Treatment with dilute mineral acids produces corresponding calcium salts with liberation of CO2: CaCO3 + 2HNO3 Ca(NO3)2 + H2O + CO2(g) In this experiment‚ the mineral acid is added in excess to the calcium carbonate and the excess titrated against standard sodium hydroxide. This kind of titration
Premium Calcium carbonate Titration Calcium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
Abstract: This report presents the reason why the ocean does not freeze in the winter. Since the ocean consists of salt water‚ an experiment was done to test the effect of freezing on salt water compared to pure water. The experiment was conducted three times in order to obtain accurate results and eliminate errors. In addition to the salt and pure water experiment‚ a variation of this experiment was created to test other options. In the variation experiment the effect of freezing on sugar water
Premium Water
Alberta Tar Sands Sustainability Report Introduction Tar sands are a combination of clay‚ sand‚ water‚ and bitumen. As a type of unconventional petroleum deposit‚ tar sands are found in many places worldwide‚ the largest deposits are found in Alberta‚ Canada. The Alberta tar sand deposits contain more than 70.8% of the world ’s reserves of natural bitumen which representing 40% of the world’s combined extra-heavy crude oil and crude bitumen reserves. It is the only bitumen deposits that are economically
Premium Petroleum Oil sands
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
LAB REPORT Introduction: In a chemical change‚ the identities of substances change and new substances form. In an equation the substances on the left are the reactants. The substances on the right are the products. In this experiment the objectives are to observe evidence that a chemical change has taken place. Infer from observations that a new substance has been formed. Identify and record observations that show energy is involved in chemical change observe the color‚ solubility of some substances
Premium Chemical reaction Chemistry Hydrogen