the question you tried to answer. Answer: How salt effects the temperature of the water hot and cold? (3 points) 2. Which observations or experiences helped you form your hypothesis? Answer: When I did beaker A which was cold with salt. And When I did beakers B-D that were hot with salt. (3 points) 3. State your hypothesis. Answer: If the water is cold with salt what way does the temperature go up or down. Verses if the water is hot with salt. (15 points) 4. Use the data from Part 1 of
Premium Potassium Chlorine Salt
electrode in another beaker. 4. Attach the electrodes to the voltmeter. 5. Roll a lengthy piece of paper towel and wet it with sodium chloride (salt bridge ) 6. Place each end of the salt bridge in the beakers. Make sure it’s dipped in the electrolyte solution. 7. Apparatus should be set as in the diagram below. 8. Keep spraying the salt bridge with sodium chloride to keep moist. 9. Record the voltmeter reading and observe clearly for any changes. 10. Repeat step 2 to 9 for
Premium Electrochemistry Battery Sodium chloride
solid 15x150mm test tube clamp watch acetone Ice cyclohexane sodium chloride Lab Safety: Wear protective googles‚ apron‚ and gloves. Procedures: Prepare ice/salt/water bath Place 50g of solid NaCl in a 400mL beaker and add just enough water to dissolve the salt. Fill an 800mL beaker 2/3 full of ice‚ and then pour salt water mixture into the beaker‚ stir. In the hood‚ into two nested test tubes‚ add 10 mL of cyclohexane from a buret. Record initial and final buret readings. Then measure
Premium Sodium chloride Gas Mass
Introduction : Copper(II) sulphate‚ is a type of salt which it is formed by combining both copper ion and sulphate ion through the experiment of double displacement between dilute sulphuric acid ‚ and copper(II) carbonate ‚ . Through this process‚ the copper ion will displace the hydrogen ion as it is more electropositive and sulphate ion will displace carbonate ion as it is more electronegative. The resulting copper (II) sulphate solution when cooled can easily crystalize
Premium Sulfuric acid Sulfur Carbon
mass an object has. Adding salt to the water adjusted the water. Squeeze the bottle hard enough‚ putting pressure to the packet. This causes the bubbles to get smaller and the entire packet to become more dense. Objective: The objective of this experiment is to find the density and buoyancy which is an upward force exerted by a fluid. Hypothesis: Think that all the packages are going to float and when squeezed‚ the package elevates more. It will sink as you add more salt Materials: A 1 liter
Premium Water Condiment Salt
all different shapes‚ abt .25 inch‚ cloudy color.After crushing: breaks into different sized shards‚ some smaller crystals‚ Wet: Salt mostly dissolves although layer of tiny granules is visible at bottom of water bubble. | c) Appearance of sand | Dry: multicolored‚ different shapes and sizes‚ generallty smaller than the salt crystals‚ very hard‚ not as sharp as salt crystals. Feels course. Some grains look more uniform to each other than others do.Wet: did not dissolve. Seemingly unchanged. |
Premium Color Water Sodium chloride
square of paper‚ carefully remove the plastic and allow all the iron to fall onto the paper. Weigh and determine the net mass of the iron powder/filings. 2. Separating out the Sand a. Put the remaining mixture‚ containing sand‚ benzoic acid‚ and table salt into your beaker and add 50 mL of distilled water. b. Set up the beaker stand and burner fuel and heat the beaker of solids and water to near boiling. Stir the mixture to make sure all soluble material dissolves. At this point‚ the benzoic acid and
Premium Water Sodium chloride Salt
spread salt daily on your driveway to melt the snow. In the springtime‚ when the lawn begins to grow‚ you noticed that there is no grass growing for about 3 inches from the driveway. Furthermore‚ the grass seems to be growing more slowly up to 1 foot from the driveway. Question: Might grass growth be inhibited by salt? Introduction: The chemical components that make up salt are the fused elements of sodium and chloride (Editorial Board‚ 2012). If there is abundance or very little salts present
Premium Sodium chloride Water Salt
750 ml of tap water 5 teaspoons of common salt 1 teaspoon 6. Method: 1. Wash each nail to remove any traces of grease or dust‚ and then rub each nail with steel wool. 2. Fill each of the glass containers with 150ml of the tap water 3. Mix ½ a teaspoon of salt in one container until dissolved 4. Repeat the process with 3 of the other containers increasing the amount of salt used by ½ a teaspoon each time so the 2nd will have 1
Premium Oxygen Sodium chloride Sodium
occurs when water becomes tightly attracted to a metal salt base on it’s polarity. The water molecules maintain integrity as molecules‚ however they are considered to be part of the formula of the hydrate. When the hydrate metal salt crystal is heated‚ the attractions to the water are broken by the heat energy and the water escape from the crystal. After heating the salt crystal is called as anhydrous‚ which means without water. Many of the salt contain transition metals such as cobalt that is colorful
Premium Water Salt Sodium