Page 1/3 09/2010 SE 110.22 Forces in an Overdeterminate Truss The picture shows SE 110.22 in a frame similar to SE 112. * Comparison of forces in statically determinate and overdeterminate trusses1 * Bars with strain gauge full bridges to measure bar force1 * Computerised evaluation of experiments Technical Description Overdeterminate trusses are employed where overdimensioning is purposely required because safety must be maintained in the event of failure of an element‚ such as in aircraft
Premium Beam Force Truss
Purpose To check whether mass is gained or lost during a Chemical reaction. Hypothesis Equipments and Materials • Eye protection • Test tube • 250 ml Erlenmeyer flask and stopper • Weight Balance • Antacid tablet • Dilute solutions of o Sodium Hydroxide‚ NaOH(aq) o Iron(III) Nitrate‚ Fe(NO3)3 • Funnel • Cylinder Procedures 1. Put eye protection on for safety purposes. Part A: Reaction between Iron(III) Nitrate and Sodium Hydroxide. 2. Take two cylinders and fill one (full)
Free Sodium hydroxide Chemistry Sodium
The starting material for this lab was the dialyzed sample (stored at -20ᵒ C) from the previous lab. The CM sephadex resin (taken in a 50 mL tube) was already made swollen using Buffer C (20 mM HEPES‚ pH 7.9; 1 mM EDTA; 50 mM KCl). The dialyzed sample was thawed to the room temperature and gently poured over the resin. The tube was capped and kept on a rocker at room temperature for 1 hour. The tube was then centrifuged in a HS-4 rotor at 2500 rpm (1200g) for 5 minutes at 4ᵒ C. Supernatant was discarded
Premium Laboratory glassware Laboratory equipment Chemistry
reaction started immediately with concomitant formation of a brown precipitate of crude acetanilide. 50ml of water and a magnetic stirring bar were added to stir the reaction mixture and the flask was heated on a magnetic stirring hot plate until all of the solid and oil were dissolved. The temperature of the reaction mixture at this point was close to 100°C‚ the boiling point of water. A few milliliters of hot solution was removed from the flask with a disposable pipette and placed in a test tube
Premium Carbon Water Temperature
If only they knew what was in the mystery mixture. After a long time of experimenting‚ the 8th grade scientist came to a decision on how they are going to figure what is in the mystery mixture. Once they started‚ they all looked at its physical properties. Then the scientists thought about the chemical reactions‚ and how that will help the claim the scientists had. More than half of the scientists thought it was baking soda and citric acid. When combining baking soda and citric acid together‚ the
Premium Chemical substance Chemistry Test method
Joshua Berkebile 8-26-10 1st period Density Lab The purpose of this lab was to find the mass‚ the length‚ the width and the height of 4 different cubes so we could calculate the volume and density of them. We also had to find the density of irregular shapes by dropping them into a graduated cylinder than subtracting the starting water volume by the ending water volume. Density is how much mass is in a certain volume of matter. Volume is the amount of room that an object
Premium Chemistry Density Temperature
Proteins (ACTIVITY 8) Gallemit‚ Lacei Machelle• • January 17‚ 2013 ABSTRACT Chromatography is one of the most useful methods of separating minute amounts of complex mixtures into the pure substances contained therein. Chromatographic separations are effected by allowing the components in the mixture to be distributed in two phases‚ one being stationary‚ and the other‚ mobile. Partition chromatography involves two main distribution systems‚ one system is composed of a gas and a liquid and
Premium Amino acid Chromatography Protein
Introduction The purpose of this lab was to identify unknown bacteria cultures using various differential tests‚ and my unknown bacteria is #17. The identification of these unknown cultures was accomplished by separating and differentiating possible bacteria based on specific biochemical characteristics. Whether the tests performed identified specific enzymatic reactions or metabolic pathways‚ each was used in a way to help recognize those specifics and identify the unknown cultures. The differential
Premium Gram staining Staining Microbiology
Ciara Clark and Caroline Bedenbaugh 4A Density Lab Objective : The purpose of this lab is to observe and explore the relationship of a substance’s volume vs. its mass‚ and to calculate an object’s density by using the relationship of its mass and volume. Data Tables : Data: Density of Water Run Mass of graduated cylinder volume of water added mass of water 1 25.28 g 0.00 mL 0.00 g 2 26.15 g 1.00 mL 0.87 g 3 27.18 g 2.00 mL 1.90 g 4 28.19 g 3.00 mL 2.91 g 5 29.13 g 4.00 mL
Premium Density Volume Data analysis
CHEM 2123 and 2125 – Organic Chemistry Lab I and II GUIDELINES FOR WRITING LAB REPORTS INTRODUCTION Writing reports in organic chemistry lab may differ from the way it’s done in general chemistry. One goal of this course is to introduce you to the record keeping methods used in research labs. Such methods are designed to organize experimental data in a format similar to that required for publication in major scientific journals. Here are some important considerations that apply in research settings
Premium Chemistry