The electron transfer reaction between hexacyanoferrate (III) and sodium borohydride resulted in the formation of hexacyanoferrate (II) ion and dihydrogen borate ion which was strongly catalyzed by AuNPs. The redox reaction is described as BH4- + 8 [Fe (CN)6]3- + 3H2O 8 [Fe(CN)6]4- + H2 BO3- + 8H+ The advantage of hexacyanoferrate ion for this redox study is that both oxidation states of iron (+2 and +3) are quite stable with respect to dissociation and hydrolysis
Premium Hydrogen Carbon dioxide Carbon
LU 1 - Tutorial 1. Write the formulas for the following compounds: Compound Copper (II) chloride Iron(II) sulphate Sodium sulphate Ammonium nitrate Sodium nitrite Potassium sulphate Magnesium phosphate Formula Compound Lithium acetate Manganese (IV) nitrate Potassium permanganate Iron (III) oxide Potassium sulphite Potassium hydrogen carbonate Sodium iodate Formula 2. Express the following numbers in scientific notation: a) 0.000000027 b) 356 c) 47 764 d) 0.096 3. Express the following numbers
Premium Chemistry Water Sulfuric acid
However‚ for Quick-eze‚ the number of moles is 0.00216 moles (1 tablet). This means the average volume of the NaOH have affected the number of moles as the concentration of the sodium hydroxide is 0.1M. This means that if less NaOH was required to neutralise the acid‚ the number of moles of HCl neutralized by the ant-acid would be greater. For example; by using mole ratio‚ the number of moles of HCl reacted with the NaOH is 0.00216 moles (1 tablet of Quick-eze). The number of moles of HCl that were
Premium Acid Chemistry Water
Experiment 7 INVESTIGATING STOICHIOMETRY WITH SODIUM SALTS OF CARBONIC ACID Introduction In this experiment we are going to get a better understanding of chemical stoichiometry. We are going to be reacting sodium bicarbonate (NaHCO3) and sodium carbonate (Na2CO3) with hydrochloric acid (HCl). To start off the mass of two unknown substances (being the sodium bicarbonate and sodium carbonate) will be taken. We will need to construct balanced equations for both of the reactants with the HCl and
Premium Hydrochloric acid Sodium chloride Chlorine
through the ice faster since they have a heavier density than water and stop the molecules from staying ice faster‚ consequently raising the temperature of the solution‚ than lower density salts would. . The data I collected shows potassium chloride‚ which has a density of 1.98 g/㎤‚ increased the solution’s temperature at a faster rate than any of the other solutions. Using the data I collected‚ I can unequivocally state that my data did not support my hypothesis. Potassium chloride had the fifth highest
Premium Chemistry Chemical reaction Temperature
production. b) Styrene - butadiene rubberStyrene - butadiene rubber (SBR) is the most important synthetic rubber‚ a copolymer of butadiene (C4 H6) and as with most polymers the raw material is petroleum. Butadiene rubber BR is important mainly in combination with other rubbers. Compounded with natural rubber and styrene- butadiene in the production of automotive tires. The process for creating styrene-butadiene rubber was through an emulsion procedure that used polymerization as the means of producing
Premium Sodium Sodium chloride Sodium hydroxide
FormulaMolecular Weight (g/mol)Density(g/cm3)Melting Point(oC)Boiling Point(oC)HazardO-vanillinC8H8O3152.15-42.5265-266Harmful andIrritantFor all 3vanillinC8H8O3152.151.05680-81285isovanillinC8H8O3152.15-113-115179Vanillyl alcohol*C8H10O3154.17-113-115--Sodium hydroxide**NaOH39.992.13181390CorrosiveHydrochloric acidHCl36.461.18-26110CorrosiveSodium borohydrideNaBH437.831.074505400IrritantCorrosive*Vanillyl alcohol is soluble in cold organic solvents such as ether/alcohol and hot water‚ but insoluble in
Premium Solvent Chemistry Alcohol
and t-Pentyl Chloride | | Jessica | [Pick the date] | Abstract The synthesis of the alkyl halide n-Butyl Bromide from alcohol is the foundation for the experiment. During the isolation of the n-butyl bromide‚ the crude product is washed with sulfuric acid‚ water‚ and sodium bicarbonate to remove any remaining acid or n-butyl alcohol. The primary alkyl halide halide n-butyl bromide is prepared by allowing n-butyl alcohol to react with sodium bromide and sulfuric acid. The sodium bromide reacts
Premium Chromatography Carbon Sulfuric acid
Introduction When iron is mixed to Copper (Ⅱ) Chloride; the product will be copper and iron chloride. However‚ in this experiment‚ we do not have the information of the oxidation number for iron nails. There are 2 different oxidation numbers for iron; that are 2 or 3. We will need to check each of the equations to find out the moles of each element in the equation. Then we can compare the ratio between the mole and the mass of iron and copper; that will be measured during the experiment. Finally
Free Stoichiometry Iron Yield
Science Investigation Srategy I am ivestigating the reaction of sodium thiosulphate and hydroclohric acid. sodium thiosulphate(aq) + Hydroclohric Acid (aq) --> Sodium cloride (aq) + Sulphur Dioxide (g) + Water (l) + Suplhur (s) Na(2)S(2)O(3) + 2 HCl --> 2NaCl + SO(2) + H(2)O + S The finished reaction of the 2 clear liquids is cloudy.I will use this change from clear to cloudy as an indicator as to when the reaction is finished. By using this change ‚ i can see the effect of changing
Premium