Part A: Diffusion on a liquid in a liquid. I did an experiment with three different glasses of tap water from the faucet. All three cups measured the same which happened to be 13 cm from the top of the cup to the bottom of the cup. I let the water settle‚ and sit for about an hour so the temperature was the same for all three cups. I then placed one drop of food coloring into the first glass and waited for the coloring to reach the bottom. I calculated 93 seconds. I then went to the second glass
Premium Osmosis Water Diffusion
Title: Liquids and Solids Purpose: The experiment will help determine two important physical properties‚ boiling and melting point‚ of liquids and solids. Procedure: Before starting the experiment I gathered all materials appropriate for the experiment and prepare a safe environment for my experiment. I record the boiling point of the Isopropyl Alcohol and the melting point of powdered Acetamide with lab equipment such as the thermometer‚ capillary tube‚ beaker‚ test tube‚ and burner fuel
Premium Liquid Temperature Solid
between specific limits moisture contents. Below these levels they have a solid consistency and above a liquid consistency. Therefore‚ the soil has two important properties to be analyzed‚ the Liquid Limit (LL) and the Plastic Limit (PL). The Liquid Limit is the moisture content that makes the soil has a liquid behavior. The Plastic Limit is the moisture content below which the soil becomes from the plastic state to the semi-solid state‚ which means it loses the ability to be shaped and starts to become
Premium Soil Water Aquifer
A safety audit for the gas-solid fluidization experiment was conducted. The following safety concerns were found when performing the audit: operating beyond the operating limits‚ spillage of the beads‚ risk of head injury from bending over to change the beads in the apparatus or from the low bar‚ and congestion of the workspace. One of the biggest safety concerns with this lab involved the small glass beads that acted as the solid in the experiment. If the gas flow rate goes below 50 standard cubic
Premium Glass Risk Causality
hardness of Specimen B is A.< 2.5 B. 2.5–3.5 C.3.5–4.5 D.4.5–5.5 Correct E. > 5.5 Answer Key: E Question 4 of 34 3.0/ 3.0 Points Specimen B is A.fluorite. B.calcite. Correct C.quartz. D.feldspar. Answer Key: C Question 5 of 34 3.0/ 3.0 Points Specimen C has Correct A.cleavage in one plane. B.cleavage in two planes at 90º angles. C.cleave in three planes not at 90º angles. D.cleavage in three planes at 90º angles. Answer Key: A Question 6 of 34 3.0/
Premium Mineral
The Molar Mass of a Volatile Liquid Adam Kozdrowicz Adam Li 11/05/12 Mr. McCready Purpose: The purpose of this procedure is to determine the molar mass of an unknown liquid‚ evaporate a sample of a liquid substance‚ and measure certain physical properties of the substance as it condenses. Procedure: 1. Obtain safety goggles. 2. Trim a piece of aluminum foil so that it covers the top of a small 13 x 100 mm test tube. Secure the foil with electrical tape. Make sure
Premium Gas
CHM130 Lab 5 The Atomic Mass of Beanium Name: Paige Miller A. Data Table: Insert your Data Table here with your sample calculations. You must show at least one sample calculation per procedure step. (16 points) Part I Data Table Sample Mass (mg) Number/Qty Average Mass (mg) Relative Abundance Relative Weight (mg) Kidneybeanium 1660.00 mg 3 553.33 mg 0.2143 118.58 mg Pintobeanium 2830.00 mg 6 471.67 mg 0.4286 202.16 mg Blackeyedpeaium 1110.00 mg 5 222.00 mg
Premium Atom Chlorine Atomic number
Title: Separation of a Mixture of Solids Purpose: Learn and demonstrate how to separate different ingredients from a mixture of solids using different methods based on the properties of each ingredient. Procedure: I weighed mixture and tools‚ and proceeded to begin separating each ingredient. I used a magnet to separate the iron from the mixture. Then I heated the mixture in water to get the non-soluble sand out. Then I filtered out the benzoic acid after cooling it into a crystal form
Premium Water Evaporation
The Purity and Purification of Solids Melting Point Lab Introduction: The point of this lab was to determine the eutectic point for the naphthalene biphenyl mixture‚ as well as determining the melting point of an unknown substance by comparing it with two known samples. Melting point is a temperature in which a substance changes from solid state to liquid state. Melting points are used to determine whether the given substance is pure or not. Substances that melt sharply‚ less than 1-2°C indicates
Premium Chemical substance Melting point Mixture
Experiment #1: Determination of the Solid-Liquid Phase Diagram for Napthalene-Biphenyl Using Thermal Analysis Objective To apply thermal analysis to the two-component system‚ naphthalene-biphenyl at atmospheric temperature. The analysis will be represented by a solid-liquid phase diagram (freezing point diagram). Theoretical Principles Phase Equilibria and the Gibbs Phase Rule This experiment is conducted in order to study a condensed system (solid-liquid) at constant temperature (atmospheric
Premium Phase