PRE LAB REPORT Reynaldo Riboul TLC and Column Chromatography October 6‚ 2013 Table of Chemicals: Chemical Hazards Mol. Wt. Density Grams Moles Acetone Flammable‚ Irritant 58.08 g mol−1 0.791 g cm−3 2.0 g 0.0344 Hexane Flammable‚ Irritant‚ Dangerous to Environment 86.18 g mol−1 .6548 g mL−1 9.0 g 0.1044 Fluorene Very toxic to aquatic life with long lasting effects 166.223 g/mol 1.202 g/mL 0.3 g 0.00180 Fluorenone Irritant 180.20 g mol−1 1.13 g/cm3 0.3 g 0.00166
Free Solvent Oxygen Laboratory glassware
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
Sample Short Lab Report By Charles M Borener Jr April 24‚ 2009 Kinetic Friction Experiment #13 Joe Solution E00123456 Partner - Jane Answers PHY 221 Lab Instructor – Chuck Borener Thursday‚ 11 AM – 1 PM Lecture Instructor – Dr. Jacobs Abstract In this experiment‚ we test factors which effect friction. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface effects friction. We found that the surface area of the block did not change
Free Force Friction Mass
aqueous layer contains sodium hydroxide and water‚ whereas the organic layer contains the dichloromethane‚ aspirin‚ and the unknown. If the HCl has nothing to react with in the aqueous layer following mixing (i.e.‚ sodium acetylsalicylate)‚ then little to no solid aspirin will be produced. Furthermore‚ more unknown would be produced than expected because aspirin would precipitate with the unknown during distillation. (c) Mistakenly extracting the dichloromethane solution with 5% HCl rather than
Premium PH Chemistry Hydrochloric acid
student : Duru Aksoy Name of the instructor: Serenay Tarhan Güler Criteria to be evaluated: DCP and CE Introduction The purpose of this investigation is to determine the concentration of an hydrochloric acid (HCl) solution by titrating it with sodium hydroxide (NaOH) solution of accurately known concentration. Titration is a common laboratory method of quantitative chemical analysis that is used to determine the unknown concentration of an identified analyte.¹ Titrant means substance with known
Premium Titration Chlorine Sodium hydroxide
The Virtual Lab – ELISA Test Lab: Immunology 09/04/2013 Instructors: Dr. Charlie Wilson Written by: Dipen Patel I. Objective: The purpose of the lab was to learn the procedure of performing an ELISA test to determine whether a particular antibody is present in a patient’s blood sample. ELISA is an abbreviation for “Enzyme-linked Immunosorbent Assay." II. Introduction: The interaction of antigen and antibody outside the body can be used to determine if patient
Premium Antibody Immune system ELISA
The purpose of the lab was to measure the effectiveness of antacids at neutralizing excess stomach acid. A neutralization reaction is when an acid and a base react to form water and salt. To illustrate‚ H+ hydrogen ions from the acid react with the hydroxide ions OH- from the base. Antacids are taken to relieve heartburn or indigestion caused by excess stomach acid. For instance‚ antacids such as alka-seltzers contain baking soda which is highly reactive with acids‚ settling the discomfort of indigestion
Premium
A pasteur pipet was then used to transfer 4ml of anhydrous ether to the vial. The syringe was then utilized to transfer 0.8 ml of this solution and the reaction was allowed to proceed until the solution turns brown and cloudy. The conical vial was then rinsed with 2 ml of anhydrous ether to get any remaining solution into the reaction vessel. Simultaneously‚ 1.09 g of benzophenone and 2ml of anhydrous ether were added to a 3ml conical vial and gently stirred. The reaction vessel
Premium Chemistry Water Solvent
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
The solubility of calcium hydroxide Aim: to find out the solubility of a substance that only partially dissolves in water. Method: place about 100cm3 of distilled water in a flask and add about one spatula of solid calcium hydroxide. Stopper the flask and shake well for one minute. Leave to stand for at least 24 hours. Titrate 10cm3 samples against 0.05 mol dm-3 hydrochloric acid solution using methyl orange as an indicator. Obtain enough results to calculate an accurate average‚ and then
Premium Calcium carbonate PH indicator Base