Determining the Stoichiometry of Chemical Reactions Mrs. Farrales Nikita Pandya October 23‚ 2012 December 3‚ 2012 INRODUCTION In the method of continuous variations the total number of moles of reactants is kept constant for the series of measurements. Each measurement is made with a different mole ratio of reactants. A mole ratio
Premium Chemical reaction Chemistry Hydrogen
Ocean County College Department of Chemistry Stoichiometry of a Precipitation Reaction Submitted by Hendy Zelishovsky Date Submitted: 4/26/2012 Date Performed: 4/25/2012 Lab Section: Chem-180-DL1 Course Instructor: Dr. Cynthia Spencer Purpose
Premium Stoichiometry Yield Water
4‚5‚ and 6 Study Guide Chapter 4 - Chemical Quantities and Aqueous Reactions * Reactions Stoichiometry * mole-mole conversions * mass-mass conversions * Limiting Reactants * What is the Limiting Reagent * How do we find the L.R. * Solutions * Molarity - definition and how to calculate * Dilutions Calculations (M1V1 = M2V2‚ careful with M2) * Solution Stoichiometry * volume-volume conversions * volume-mass conversions
Premium Chemistry Chemical reaction Chlorine
AP Chemistry Unit 2 Notes Stoichiometry You should understand all that is presented in chapter 3 of your text (Zumdahl: Chemistry‚ 8th edition). Some of the highlights are presented below. Atomic Masses (Section 3.1) Nearly every element is made up of atoms of more than one isotope for that element. A few‚ like Be‚ only have one isotope. Others can have a large number of isotopes. Tin (Sn) has ten isotopes. (No pun intended.) Isotopic abundance is determined by the use of
Premium Stoichiometry
Practicum 2: Stoichiometry of Chemical Reactions Written by: Ade Istianto (2014990003) Aprizky Bagus Heldinto (2014990002) Deas Pratama (2014360004) Paskah Andreas Deo Gratias (2014370005) Sampoerna University ABSTRACT This experiment is endure to determine and study about the stoichiometry of chemical reactions in certain chemicals. The experiments were to make sure student are able to use and learn the Job’s method-the method of continuous variation-for determine the reaction stoichiometry. In the
Premium Chemical reaction Chemistry Mole
The progress of the reaction was monitored in my case using two TLC plate. It first started off with the spotting of Standard benzoin and benzil which were provided in the lab and followed by the addition of the reaction mixture at once it starts changing colour/boiling‚ then at 10 and 20 mins into the reflux. Once all the necessary steps were spotted‚ the TLC plate was placed in in a beaker containing CH₂Cl₂(methylene chloride)‚ which was used as the developing solvent in this experiment. To check
Premium Chemistry Chemical reaction Thin layer chromatography
Purpose: In this experiment I will predict the amount of product produced in a precipitation reaction using stoichiometry by accurately measuring the reactants and products of the reaction. I will also determine the actual yield vs. the theoretical yield by calculating the percent yield. Materials: 1 Distilled water 1 Paper towels 1 Small paper cup 1 Coffee cup or mug 1 Beaker‚ 100 mL‚ glass 1 Funnel 1 Cylinder‚ 25 mL 1 Goggles-Safety 1 Scale-Digital-500g 1 Weighing boat‚ Plastic 1 CaCl2·2 H2O-Calcium
Premium Chemistry Water Chemical reaction
Lab 3: Stoichiometry of a Precipitation Reaction NOTE: All photos should be taken so the reading on the electronic balance is readable. Photo 1: filter paper being weighed on electronic balance‚ along with your student information card. Photo 2: beaker with precipitate slurry in it (after step 5) ‚ along with your student information card Photo 3: dried precipitate/filter paper being weighed on electronic balance‚ along with your student information card Additional Question Guidelines:
Premium Water Chemistry Solid
Using Stoichiometry to Determine Gases Produced in a Reaction Introduction Magnesium is a metal and is the third most commonly used metal by chemists. Some would say it is the least dense structural metal. Its lightness is often alloyed with aluminum. Magnesium is also used in racing car wheels called MAG wheels. Many car-manufacturing companies will use magnesium and aluminum because of the lightness of the metal. Both of these metals are reactive with acids. The most common acid in they
Premium Pressure Gas Hydrogen
2Fe+3 --> something + 2Fe+2 Equation 2: 8H+ + 5Fe+2 + MnO4- --> 5Fe+3 + Mn+2 + 4H2O Equation 3: 6H+ + 2MnO4- + 5H2C2O4 --> 2Mn+2 + 10CO2 + 8H2O Conclusion: Therefore the concluded reaction would be: NH3OH+ + 2Fe+3 --> N2O + 2Fe+2 This was obtained by using stoichiometry half reactions the product of that reaction was determined to be N2O. Some systematic errors could be if the wrong molarity was determined for the permanganate because then that would though off the calculations for the Fe+2 and
Free Manganese Mole Potassium permanganate