| |Formal Report 1 | | | |Experiment Number 3 | | | |Chem201L | | Determination of
Premium Chemical compound Chemistry Melting point
Title Freezing and Melting Point Objectives 1. To gain proficiency in constructing a graph and plotting data points. 2. To determine the freezing points of a compound from the graph of decreasing temperature versus time. 3. To determine the melting points of a known and unknown compound. Introduction Physical changes are the changes in the physical properties of a substance (Moore‚ Stanitski & Jurs‚ 2009). Freezing point is the fixed temperature at which a pure liquid converted into crystalline
Premium Melting point Liquid Chemistry
Lab #1: Melting Points of Organic Compounds Report Form May 15‚ 2014 1. A “Melting Point Range” refers to the range of temperature at which a solid melts into its liquid state. 2. Pure compounds have narrow or ‘sharp’ melting point ranges‚ 1°C or less if the compound is very pure. A less pure compound exhibits a broader melting point range‚ between 3°C to 10°C as well as a depressed or lower range. 3. Crushing the sample allows for greater surface area-to-volume ratio of the powder‚ this
Premium Temperature Thermodynamics Heat
SUBLIMATION Sublimation is a technique used by chemists to purify compounds. Typically a solid is placed in a vessel which is then heated under vacuum. Under this reduced pressure the solid volatilizes and condenses as a purified compound on a cooled surface‚ leaving the non-volatile impurities behind. This cooled surface often takes the form of a "cold finger" (shown in the diagram above). Once heating ceases and the vacuum is released‚ the sublimed compound can be collected from the cooled surface
Premium Gas Carbon dioxide Temperature
Melting Point Determination and Thermometer Calibration Lab Background: The melting point of a substance‚ a solid in this case‚ signifies the temperature at which the first crystal starts to melt until the temperature at which the last crystal disappears is reached. That being said‚ melting points are expressed in ranges‚ am organic compound will have a sharp range depending on the purity of the compound. Impurity of an organic substance will register an abnormal melting point based on its
Premium Salicylic acid Temperature Chemical compound
Crystallization and Melting Points Organic Chemistry 221 9/19/2012 Intro/Purpose: The purpose of this lab was to use crystallization to separate a compound from a solvent and be able to choose the best solvent to do so. Then identify an unknown and verify purity using melting points. Solubility contributes to crystallization; because a solute has lower solubility at lower temperatures‚ which makes the solvent separate from the solution as a solid. This process is important to understand because
Premium Solubility Chemical polarity
Organic chemistry 201 | Mixed Melting Points | Determination of an Unknown Solid | | [Type the author name] | 9/15/2011 | Purpose : The main purpose of this experiment was to identify an unknown compound/substance by performing multiple experimental melting point tests. Pure and impure solids were tested to see what affect pureness/impureness had on a melting point. Background: The melting point of a solid can be used to determine the purity of the solid. Pure samples usually have
Premium Atom Chemistry Oxygen
Recrystallization and Melting Point of Benzoic Acid Organic Chemistry 1 10/4/12 Abstract Recrystallization was done to remove impurities from the sample. The percent recovery of benzoic acid during recrystallization is 23.02%. The difference between the pure and impure samples was observed by comparison of melting points. It was found that impure sample had a lower and wider melting point range of 120.1-122.2 (C). The pure sample melting point range was 121.3-122.5 (C). These ranges helped determine
Premium Solubility
Engineering and Chemistry Muralla St.‚ Intramuros‚ Manila Melting Point and Boiling Point of Organic Compounds Group No. 5 Manacup‚ Cris Vincent L. Oblena‚ Adrian D. Ong‚ Joshua Jyro B.* *Leader ABSTRACT In compounds‚ two of the physical properties affected by the varying structures are melting point and boiling point. Through the use of the Thomas-Hoover Melting Point Apparatus or the micro method‚ the melting and boiling point of organic compounds are now determined. The aim of this
Premium Hydrogen bond Carboxylic acid Melting point
Sample Lab Report for CHM 152 Name Lab Partner(s) Abstract: The physical properties‚ including the boiling point‚ density‚ and refractive index were measured for unknown liquid #16. The infrared (IR) spectrum of the compound was also taken. Based on the data collected‚ it was determined that the compound was likely to be salicylaldehyde. Introduction The purpose of this experiment was to determine the identity of an unknown organic liquid by measuring some of its physical
Premium Temperature Liquid Fundamental physics concepts