Abstract The glass transition temperature of polymethylmethacrylate ( PMMA‚ Perspex) is measured using static and dynamic method while the glass transition temperature of rubber of different size is measured using only dynamic method. The glass transition temperature Tg of Perspex is found to be 90°C using the static method and 160°c using the dynamic method. On the other hand‚ the Tg of rubber is found to be -30°C. Introduction Perspex is a type of amorphous polymer and has the following
Premium Temperature Heat Polymer
11 physics: SPH3U1-01 | Physics Lab Report | Specific Heat Capacity of Brass | | Jin Jin Shi | 2012/12/6 | Instructor: Mr. Nailer | I. Introduction The amount of heat required to raise the temperature of a solid body depends on its change in temperature (ΔT)‚ its mass (m)‚ and an intrinsic characteristic of the material forming the body called specific heat (cp). The heat is calculated from the equation II. Purpose The purpose of this laboratory is to determine the
Premium Heat Specific heat capacity Thermodynamics
measure the enthalpy (H) of a chemical reaction. The main obstacle is that this is a quantity that cannot be measured directly. It instead is observed as heat from one substance is transferred to another while being monitored with a thermometer. A temperature change in a known substance (such as water) can be related to a certain amount of heat (q). q mass T f Ti Specific heat Our calorimeter is going to be a set of Styrofoam coffee cups. These cups are well known insulators‚ and they
Free Thermodynamics Energy Hydrogen peroxide
HEAT OF FUSION OF ICE Introduction When heat flows into a system there are a number of things that can happen. One result could be a temperature rise. Or‚ the system might even catch fire. A third possibility is a change of state. As you know‚ matter exists in three states (or maybe four‚ the fourth being a plasma)‚ solid‚ liquid and gaseous. At different temperatures‚ the same substance may be in different states. Each state is characterized by the way the interatomic forces act. In solids‚ the atoms
Premium Energy Solid Temperature
Ectotherms and Endotherms- temperature regulation Part A :Types of Temperature regulation 1. Write down the meaning of the terms endotherm and ectotherm. Consult a textbook if necessary. a. endotherm Endotherms are animals that can maintain a constant internal body temperature. For instance mammals and birds are true endotherms that can maintain a constant internal body temperature b. ectotherm Ectotherms are animals that are not able to regulate their body temperature or in simple words‚ they
Premium Temperature Energy Thermodynamics
REPRESENTATION OF DATA 1. Pressure versus temperature (P-T) 2. Pressure vs. volume (P-v) 3. Temperature vs. volume (T-v) 4. Temperature vs. entropy (T-s) 5. Enthalpy vs. entropy (h-s) 6. Pressure vs. enthalpy (P-h) The term saturation temperature designates the temperature at which vaporization takes place. For water at 99.6 C the saturation pressure is 0.1 M Pa‚ and for water at 0.1 Mpa‚ the saturation temperature is 99.6 C. If a substance exists
Free Thermodynamics Temperature Boiling point
|decreases|increases| 4. Two bodies are brought into thermal contact with each other. No thermal energy transfer takes place between the bodies. It may be deduced therefore‚ that the bodies must have the same A. specific heat capacity. B. heat capacity. C. temperature. D. internal energy. 5. An ideal gas expands isothermally‚ doing 2500 J of external work in the process. The thermal energy absorbed by the gas in this process is A. zero. B. less than 2500 J. C. equal to 2500 J. D. more than 2500 J. 6. Which
Premium Temperature Thermodynamics Energy
cooling water inlet temperature‚ cooling water outlet temperature are vary according to ambient conditions. At the starting of procedure at the starting of experience i.e. on 2:00PM the reading of Air DBT‚ Air WBT‚ cooling inlet‚ cooling water outlet temperature are as follows: At 2:00PM (i.e. starting procedure) all temperature readings are shown in table below. Table 6.1 At 2:00PM (i.e. Starting Procedure) all Temperature Reading Air DBT(0C) Air WBT(0C) Cooling Water Inlet Temperature(0C) Cooling Water
Premium Temperature Thermodynamics Heat
direct methods (changes in temperature and latent heat) and indirect method (magnetization isotherms). This compound undergoes a first-order paramagnetic to ferromagnetic transition with TC ¼ 200 K upon cooling. The paramagnetic phase becomes unstable and it transforms into a ferromagnetic phase under the application of magnetic field‚ which results in a field-induced metamagnetic transition (FIMMT). The FIMMT is accompanied by release of latent heat and temperature of the sample as evidenced from
Premium Magnetism Magnetic field Thermodynamics
FePO4: high-temperature behavior and α-β phase transition Z. Kristallogr. 218‚ 193-200 (2003). Paragraph 1 This writing exercise will be talking about how the structure of FePO4 will change from a low temperature of 294K to a high temperature of 1073K. There is a huge difference in both the cell parameters and atomic coordinates for α phase and β-phase. FePO4 changes from α phase to β-phase at about 980K. This is known as the transition phase. This phase took place at a high-temperature. In α phase
Premium Chemistry Chemical reaction Chemical kinetics