minutes and filter through a cheesecloth after they had been incubated for 15 minutes. After the solution had been made we obtain about 5 ml of the Strawberry filtrate and added it to a clean test tube. Few milliliters of cold ethanol that had been stored in the freezer was added to the
Premium
four parts to it‚ where you had to find out if the food you picked contained starch‚sugar‚lipids and protein.The food item that was chosen to decipher was a Big Mac and you chose what from the burger you wanted to test to see what it was made of‚ example like the bun of the burger. When testing you would have one test tube of water with food and the other test tube with the solution needed and food.The reason for the test tube with the water is because it was the indicator. If the product of food
Premium Nutrition Food Milk
We labeled the test tubes with numbers one through five. The first test tube was our calibration tube‚ here we added one milliliter (mL) of buffer‚ four mL of distilled water and three drops of chloroplasts using pipets. After‚ we created the solution for the second‚ third‚ fourth and fifth test tubes by adding one mL of buffer‚ three mL of distilled water one mL of DPIP an 3 drops of chloroplasts. However‚ we decided that test tube number two was going to be the test tube that was kept completely
Premium Photosynthesis Plant Oxygen
is unlimited per the lab manual.(Bluedoor) If there is no competition in the water‚ the growth can be unlimited. The population will have favorable
Premium
| | Kinetics Author: Katie Wood Instructor: Donald Kavanagh Chem 106b‚ Section 001 Lab Performed 8th‚ 2012 Lab Report Submitted February 22nd‚ 2012 Abstract The purpose of the lab was to determine the order of reaction for the dye Red #40. By measuring the reaction rate between bleach and the dye‚ the order of the reaction was determined to be first order. Introduction The study of kinetics is important for studying the amount of time it takes for a particular reaction to reach
Premium Reaction rate Rate equation Chemical kinetics
The pGLO lab is a lab where students attempt to put the genes that make a jelly fish glow into E. Coli. After a process called transformation‚ the process in which a cell takes up and expresses a new piece of genetic information‚ the E. Coli will be able to glow and will be antibiotic resistant. The students first need to learn a couple of techniques before they are able to begin this lab. The first technique they will need is how to keep their environment sterile. They must learn to only open their
Premium Bacteria Microbiology Gram staining
This lab activity will go over environmental factors that affect the folded structure of proteins. We used a raw egg and noted the changes that happen when there were changes in temperature‚ pH levels‚ and salinity. Five eggs were cracked open and placed into different bowls with different solutions placed into each bowl. What we looked at was the process of denaturing of proteins seeing how it affected the composition of the raw egg between the yoke and white portion. My hypothesis for this experiment
Premium
9/23/12 Lab Report #1 Meter Reading Summary The objective of this experiment was to learn how to read different meters like the D.C. volt meter and the D.C. amperes meter. In all meters each big line is a major division and each little line in between is a minor division‚ and if there is a line smaller than the minor division lines then that would be a sub minor division. Each meter has a low‚ medium‚ and high range. For example on the D.C. volt meter the ranges go from top to bottom 150‚ 15‚
Premium Electric current Volt Kilogram
Abstract: In this Lab we used the chemical DPIP to detect the rate of succinate broken down by the mitochondrial solution. We detected the amount of DPIP in the solution with a spectrophotometer and measuring the absorbance of light at the 600nm range. DPIP is a useful chemical to use in this experiment because it goes from a blue color when oxidized to a colorless liquid (Ogura‚ 281)‚ this is due to the hydrogen ions and electrons released during the transitional step between succinate and fumarate
Premium Chemistry Concentration Solution
having a least count of 0.001g. Each specimen was completely immersed in distilled water at 25°C. c) Scanning Electron Microscope Scanning Electron Microscope (Model: JEOL) was used to observe the fiber-matric interface of cross section of the tensile test specimens and evaluate the fracture behavior to correlate it with the tensile strength. The specimens being non-metallic‚ to enhance the conductivity‚ the specimens were coated with palladium using a sputter coater for 60 seconds at a current of 20
Premium Water Water pollution Oxygen