Investigate The Relationship Between The pressure And The Temperature For a Saturated Steam in a Constant Volume Tank. And To verify the Clausius – Claperon Equation. Apparatus : Gunt Marcet Boiler Theory: = where : T = Abs. Temp. Vfg = Vg – Vf Hfg = hf – hg Results and Calculations: Gauge Pressure (bar) Absoulte Pressure Steam Temp . Increasing Pressure Steam Decreasing Pressure Mean Temp. 0 0.9 95 97.5 96.25 1 1.9 115.2 117.7 116.45 2 2.9 129.5 132
Premium Thermodynamics Gas Temperature
NPC DOC. NO. TAPP-3/64110/5526/DN/R0---------------------------------4 13300 00 486 ---REV. NO. 01 WRITE UP ON ELECTROHYDRAULIC TURBINE CONTROLLER ( EHTC ) Reference Documents: 1.MPL for Steam Turbine Doc. No. :- 41330000488(TAPP3/64110/5516/SCH) 2.Scheme for speed measurement turbine and generator Doc. No. :- 41330098204(TAPP3/64110/5512/DN) 3.Write up on LRR for MSCV and AEOR Doc. No. :- 41330000481(TAPP3/64110/5661/DN) 4.OGA of TG control desk 6610 – PL – 9 Doc. No. :- 06560000403(TAPP3/64100/5724/GA)
Premium PID controller Control theory Control system
faucet and the ball lever assembly of the drain. | Back Vent | Plumbing fixture’s separate vent in a building drainage system. | Balancing Valve | A water heater valve that controls water flow and balances heat distribution to different locations. | Ball Check Valve | A valve that uses a ball to seal against a seat to stop flow in one direction. | Ball Joint | Spherical assembly allowing pivot rotations for showerheads. | Blind Plug | Plug used on No
Premium Plumbing
Isolation of Acetyleugenol (Clove Oil) from Cloves Purpose In this experiment‚ you will obtain the essential oil from cloves by steam distillation. You will then separate a component (acetyleugenol) from the oil by liquid-liquid extraction. Finally‚ you will isolate the acetyleugenol by using a rotovap for reduced pressure distillation‚ which will remove the organic solvent (dichloromethane). Background Whole cloves contain between 14% and 20% by weight of essential oils‚ but
Premium Distillation
Students will be able to study the fundamental pressure-temperature relationship of saturated steam in equilibrium with water. DESCRIPTION SPECIFICATIONS The unit consists of a stainless steel pressure vessel fitted with a high pressure immersion electrical heater. The unit also comes with a safety valve‚ glass thermometer and Bourdon type pressure gauge. Water inlet valve and discharge valve are also installed. i) Pressure Vessel 3 liter capacity made of stainless steel The unit
Premium Pressure Data acquisition Temperature
engines and two-stroke engines. Each has its own advantages and disadvantages. There is such a thing as an external combustion engine. A steam engine in old-fashioned trains and steam boats is the best example of an external combustion engine. The fuel (coal‚ wood‚ oil‚ whatever) in a steam engine burns outside the engine to create steam‚ and the steam creates motion inside the engine. Internal combustion is a lot more efficient (takes less fuel per mile) than external combustion‚ plus an internal
Premium Internal combustion engine
except as permitted by the Copyright Act or other law. ERB‚September 2001 Experiment or Topic Pages Preface 1 2 3 4 5 6 7 8 9 10 11 ii iii Calorimeter Capillary Tube Dynamometer Expansion Valve‚ Automatic‚ Pressure Regulation Expansion Valve‚ Automatic‚ Temperature Regulation Gasoline Engine‚ Transparent‚ Four Stroke Heat Exchanger‚ Double Pipe Heat Pump Polytropic Process (air compressor) Rankine Cycle Vapor-Compression Cycle (Refrigeration Cycle) Pre-Lab
Premium Thermodynamics Chemical engineering Heat pump
operation‚ and basic maintenance of diesel engines‚ reduction gears‚ and related auxiliary equipment and support systems; the design‚ construction‚ principles of operation‚ application‚ and basic maintenance of mechanical components such as pumps‚ valves‚ and control devices; the design‚ principles of operation‚ and basic maintenance of marine auxiliary equipment‚ specifically compressed air systems‚ distilling plants‚ evaporators‚ refrigeration and air-conditioning systems‚ deck machinery‚ steering
Premium Internal combustion engine Diesel engine
Casings of steam turbines‚ compressors‚ gas turbines. • Valves such as Globe Valve body and bonnet‚ Check Valve‚ Gate Valve. • Nozzles and chemical reactors. • Service temperatures up to about 570 °C. Gate Valve Body Globe Valve Body [pic] Advantages: • Easily Weldable with similar weld metal. • Has higher resistance to Graphitization • High Creep resistance. Limitations: • Applicable for valves operating
Premium Steel Carbon steel
relationship between pressure and temperature of saturated steam Apparatus: a Marcet boiler (Figure 1) is used. It is provided with a pressure gauge‚ a digital thermometer and a safety valve. An aneroid barometer is used to determine atmospheric pressure. 1 2 3 Drain valve Heater Overflow Variation of saturation temperature with pressure Thermodynamics Laboratory Manual Marcet boiler 4 5 6 7 8 9 Temperature sensor Pressure relief valve Filler opening with plug Pressure gauge Master switch
Premium Thermodynamics Heat Temperature