instruments like: 1. Vernier caliper‚ 2. Micrometer Screw Gauge and 3. Spherometer Screw. 1. Vernier caliper 1.1. Apparatus 1. Vernier caliper‚ and 2. Parallelepiped solid object. 1.2. Theory A very ingenious device for obtaining accuracy of a greater order than that obtainable by eye-estimation was invented by (Pierre Vernier)‚ and is known by his name. Faculty of Pharmacy | Delta University Page 2 [PRACTICAL PHYSICS I] Fall 2012 The vernier is a convenient attachment
Premium Density Viscosity Fundamental physics concepts
question. True stress and strain are calculated based on the actual dimensions of the material. Method Install the given copper cylinder into the Hounsfield H20K-W testing machines after measured the length and the diameter of it by using a Vernier caliper and a ruler. Then set the X and Y vector of machine to the zero and operate the machine. Make sure the connection between copper and the force measurement is fixed and tight before operate it. There are two value displaced on the displayer‚ one
Premium Elasticity Stress Materials science
workpiece Vernier calipers To take the varying diameter of the work piece Tool post spanner For making adjustments to the tools Chuck key Used for tightening or loosening the bolts on the chuck Parting tool To remove finished parts. Procedure • We took a mild steel round 25*80 mm long piece and set it in the chuck with the required length by the use of chuck key. • Then marked the job as per given measurements with the help of steel rule and calipers. • Did
Premium Cutting Angle
specimen and how the type of fracture for this specimen. All of this issue‚ we had been discussed more details in our discussion. In this experiment we used a tensile testing machine to elongate the specimen but we drive it manually‚ we also use a vernier caliper to measure a length of elongation of the specimen and this experiment we carrying according to procedure given. Finally‚ at the conclusion we were strictly restated our stand about the result of this experiment which were value of modulus elasticity
Premium Tensile strength Elasticity
Name of Student: Name of Partner: Date of Experiment: Date of Report: Aim In this experiment‚ we aim to: (a) determine the refractive index n of a polymer slab from its constructive and destructive thin-film microwave interference; and (b) determine the lattice constant a of an array of thin copper rods from its Bragg diffraction of the incident microwave. Introduction Thin Film Interference When plane electromagnetic wave of wavelength λ is incident on a dielectric surface‚ part
Premium Diffraction Wavelength Snell's law
16–1 COOLING – WATER PUMP ASSY (1ZZ–FE/3ZZ–FE) WATER PUMP ASSY (1ZZ–FE/3ZZ–FE) 160AO–01 INSPECTION 1. (a) INSPECT WATER PUMP ASSY Visually check the drain hole for coolant leakage. Hole B10233 1ZZ–FE‚3ZZ–FE ENGINE REPAIR MANUAL (RM923E) 14–38 ENGINE MECHANICAL – CYLINDER BLOCK (1ZZ–FE/3ZZ–FE) CYLINDER BLOCK (1ZZ–FE/3ZZ–FE) 140KO–01 COMPONENTS Compression Ring No.1 Compression Ring No.2 Oil Ring (Side Rail) Oil Ring (Expander) Piston z Snap Ring z Bush z Snap Ring Piston
Premium Internal combustion engine Connecting rod
S/N: 400667 8” Vernier Calipers S/N: 3475 9.97” x 1.0” x 0.123”Aluminum Beam Steel Reference Beam with (6) drilled measuring holes C-Clamp Shim Figure 1: Side View of Experimental Set-up Experimental Procedure 1. The three piece beam arrangement shown in Figure 1 was clamped to a table. 2. The following distances were measured: a. Edge of table to the end of the steel reference beam using calipers. b. Edge of table to center of mass hanger using calipers. c. Top of steel
Premium Experiment Measurement Cantilever
KNOWLEDGE EVIDENCE NVQ TITLE PERFORMING ENGINEERING OPERATIONS – LEVEL 2 UNIT CODE QPEO2/012 UNIT TITLE Preparing and using milling machines Note: Please type your answer in regular font. 1.) What are the safe working practices and procedures to be followed when preparing and using the milling machines? When operating a Milling machine there are a lot of health and safety laws that have to be followed when preparing to use and using a milling machine‚ the laws and safety precautions
Premium Milling machine Machining
Department of Civil Engineering G.H. Raisoni College of Engineering Hingna Road‚ Digdoh Hills‚ Nagpur – 16 Laboratory Manual THIRD SEMESTER B.E. CIVIL STRENGTH OF MATERIALS DEPARTMENT OF CIVIL ENGINEERING Strength Of Materials Department of Civil Engineering STRENGTH OF MATERIALS List of Practical 1) To Study The Universal Testing Machine (U.T.M.) 2) To determine Tensile test on a metal. 3) To determine Hardness of Mild Steel. 4) Torsion test on mild steel rod. 5) To determine Impact
Premium Materials science Tensile strength Elasticity
TABLE OF CONTENT CONTENTS PAGE NO. 1. Introduction a. Objective 3 b. Introduction 3-4 2. Material and Methodology a. Materials & Apparatus 5 b. Procedure 5 3. Results and Discussions a. Results & Calculations 6-8 b. Discussions 9-10 4. Conclusion 10 5. Reference 11 6. Appendix 12 OBJECTIVE 1. To enable students to familiarize themselves with
Premium Metal Materials science Aluminium