grid side converter is used to regulate the voltage of the DC link capacitor. Besides it satisfies the unity power factor of grid-side and bi-direction flowing ability of energy. The control model of whole system is built using Matlab/Simulink program. The proposed control structure achieved the fastest and robust dynamic response without stressing the converters or deteriorating the
Premium Wind power Renewable energy Wind turbine
application INFO available UC1638 UC2638 UC3638 Advanced PWM Motor Controller FEATURES • • • • • • • • Single or Dual Supply Operation Accurate High Speed Oscillator Differential X5 Current Sense Amplifier Bidirectional Pulse-by-Pulse Current Limiting Programmable Oscillator Amplitude and PWM Deadband Dual 500mA Totem Pole Output Drivers Dual 60V‚ 50mA Open Collector Drivers Undervoltage Lockout DESCRIPTION The UC1638 family of integrated circuits are advanced pulse width modulators intended
Premium Amplifier
Nguyen Wed 2:00-5:00 02/19/2014 OHM’S LAW I. Purpose The purpose of this lab is to help understand how voltage‚ current and resistance are closely related to one another. The outcome from this lab is to be able to differentiate when to use ohmmeter and voltmeter for the individual circuit. II. Theory Ohm’s Law states that the electric current through a material is directly proportional to the voltage across a piece of material (such as wire) while the resistance is held constant. mathematical equation
Premium Electrical resistance Resistor Ohm's law
org/wiki/Operational_amplifier Operational amplifier From Wikipedia‚ the free encyclopedia An operational amplifier ("op-amp") is a DC-coupled high-gain electronic voltage amplifier with a differential input and‚ usually‚ a single-ended output.[1] An op-amp produces an output voltage that is typically hundreds of thousands of times larger than the voltage difference between its input terminals.[2] Operational amplifiers had their origins in analog computers where they were used to do mathematical operations
Premium
Engineering University of Colorado‚ Boulder‚ CO 80309-0425 USA Abstrurt - This paper describes performance‚ design and optimization of de-dc converters for energy limited‚ battery operated systems. Variable-frequency operation is used to achieve voltage regulation and high efficiency for an extremely wide range of load currents. An experimental 15W‚ 3.3V buck converter has been constructed to demonstrate design and optimization techniques. The converter employs synchronous rectification to reduce
Premium Inductor Capacitor
ENGINEERING 01FII-C2A-S04 1. An electrical component is connected across a 120 volt‚60Hz‚AC supply.What is the current drawn by the component if the impedance is 200 ohms? Ans: 0.060 Amperes 2. A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? Ans: 122.22 Ohms 3. What power would be consumed in each of the branch resistors of the circuit if the source is 30 volts‚ the resistance
Premium Transformer Electric motor Electrical generator
compare with single-phase. 8. Describe the relationships between the individual output and resultant vectorial sum voltages in multiphase generators. 9. Explain‚ using diagrams‚ the different methods of connecting three-phase alternators and transformers. 10. List the factors that determine the frequency and voltage of the alternator output. 11. Explain the terms voltage control and voltage regulation in ac generators‚ and list the factors that affect each quantity. 12. Describe the purpose and procedure
Premium Electric motor
battery. A DC to DC converter is an electronic circuit which converts a source of direct current (DC) from one voltage level to another. DC is not easily being stepped up or down. One of the applications of this DC to DC converter is stepping down the voltage. In this experiment a Step down DC to DC converter was created. Here‚ the output voltage will become smaller than the input voltage. This type of applications is the one used for cellphones and laptops. Objectives The purposes for the
Premium Printed circuit board Electronic engineering Integrated circuit
negative temperature coefficients. 7) The amount of energy that is converted to heat at a silicon p-n junction can be a significant design consideration. 8) A normalized value has a reference magnitude of one. 9) The reverse breakdown voltage of an LED is typically less than 12 V. 10) The amount of photon energy emitted at the p-n junction of a silicon diode is negligible. 11) The characteristic of an ideal diode are those of a switch that can conduct current ________. A) in both
Premium
starting is the voltage dip that is experienced throughout an industrial power system as the direct result of starting large motors [4]. There are several general methods of starting induction motors: full voltage‚ reduced voltage‚ wye-delta‚ and part winding types. The reduced voltage type can include solid state starters‚ adjustable frequency drives‚ and autotransformers [5]. Motor starting has been investigated for decades [5-16]. The most frequent power quality events that occur are voltage sags and
Premium Electric motor Electrical engineering Transformer