1-What would not have happened if we had elected officials who hear us when we weep from whipping laws? 2- What would not have happened to our brothers in Faraba if we had elected officials who heard us when we wept? 3- What would not have happened in Gunjur beach had our youths been heard against mining? 4- What would not have happened‚ had we not been marginalized by government upon government that instituted and adopted laws and weaponized them against us to keep us in the state that we are
Premium
important questions from Hydrostatics: i. Why is it easier to lift a body in a liquid than in the air? ~ We know that‚ Upthrust =Density of fluid*acceleration due to gravity*Immersed volume of the body From the realtion above‚ it is clear that upthrust given by a fluid to a body is directly proportional to the density of the fluid. Also‚ as a matter of fact‚ the density of air is less than that of liquid. So‚ the liquid provides greater amount of upthrust than the air does. This implies that a body
Free Density Water Liquid
1. DATA: Table 1: Density based on dimensional analysis Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5466 70.5467 70.5465 g Dimensions of sample Length 4.98 4.98 4.99 cm Width 1.21 1.22 1.21 cm Height 1.21 1.22 1.22 cm Volum of sample 7.29 7.41 7.37 cm^3 Density of sample (based on dimensional analysis) 9.68 9.52 9.57 g/cm^3 Table 2: Density based on the displacement of water Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5467 70.5465 70.5466 g Final
Premium Density Volume Water
22ºc Part B Aluminum Sinker 1. Mass of object. 6.87g 49.44g 2. Volume of the water in the graduated Cylinder after the addition of the object. 17.5mL 19mL 3. Volume of the object due to displacement 2.5mL 4mL 4. Density of object. 2.748 12.36 5. Calculated mass of the sinker in ounces 1.74g Part C 1. Length of the foil 8.5cm 2. Width of the foil 8.5cm 3. Mass of the foil .60g 4. Volume of the foil .222 5. Thickness of the
Premium Density Kilogram Measurement
Measuring the Density of Ball Bearings/ Density Aaysha Dawood Chem 1211L-198 September 7‚ 2012 Procedure: The procedure for this lab was taken from the lab manual below: Block/McKelvy (2012). Laboratory Experiments for Chem 1211L & 1212L Cengage Learning (7th ed.)‚ p. 5-19 (Measuring the Density of Ball Bearings/Density). No changes occurred that were different from the procedure listed above. Data: Measuring the Density if Ball Bearings | Ball 1 | Ball 2 | Ball 3 | Ball 4 |
Premium Force Classical mechanics Mass
Experiment Density‚ Accuracy‚ Precision And Graphing OBJECTIVES 1. The determination of the density of water 2. A comparison of the accuracy and precision of a graduated cylinder and a pipet EXPERIMENTAL MATERIALS Part A A 50mL graduated cylinder A balance 50.0mL deionized water A rubber policeman Part B A 100mL beaker A 50mL graduated cylinder A volumetric pipet 120.0mL deionized water A thermometer A rubber policeman
Premium Density Volume Measurement
Lab No.1: density‚ accuracy and precision Aim: to determine the relative precision and accuracy of different glassware items by calculating the density of a known substance. Introduction: the density of a substance is its mass per unit volume. (where P-density‚ m- mass and v- volume). Different materials usually have different densities and densities vary according to the pressure‚ temperature and purity of a substance. When measuring‚ there is always a small uncertainty or error and therefore
Premium Management Scientific method Education
The Density Challenge: A Complete Inquiry Activity Introduction Density has been an important part of science for a very long time. Density was discovered by Archimedes‚ a Greek mathematician‚ around 250 BC while determining whether a craftsman had replaced some of the gold in the King of Syracuse’s crown with silver. Density is the compactness of a substance. The new concept of density he discovered was used to expose the fraud. The purpose of this experiment is to make
Premium Density Volume Water
The physical environment has determined to some extent‚ the distribution and density of Australia’s population. Discuss. People do not live evenly spread through the world. Australia is one of the counties that considered has a low population density. This is due to approximately 23 million population were distributed unevenly. Besides the physical environment‚ there are also a variety of other factors that have actually worked together to distribute in the Australia’s population that cannot be
Premium Population density
The density of fractions 1‚ 2‚ and 3 are as follows: 1.49‚ 1.325‚ and 1.34 g/mL. These values areincorrect because the density should not have been over 1.0 g/mL. This is because the density of water is 1.0 g/mL‚ and the product should have had a mixture of ethanol and water‚ making the density lower. The measured weight of the vials and ethanol were incorrect due the scales.There are many factors that can cause a scale not to read the correct value. The first is the airflow underneath the weighing
Premium Density Volume Water