potato Two pennies Two zinc-plated nails or screws Three pieces of copper wire A very small light bulb or LED light 1) Get a potato and cut it in half. Then make a small slit in each half just big enough to put a penny into. 2) Cut two pieces of copper wire and wrap one around one of the pennies a few times‚ and wrap the other one around the other penny a few times as well. 3) Take a third piece of copper wire‚ and wrap it around one of the zinc-plated nails or screws
Premium Battery Zinc Electrochemistry
mm) 4 beakers (150 mL) Safety goggles Lab apron Plastic gloves Full face shield Reagents Zinc Magnesium Iron Copper 1M hydrochloric acid‚ HCl 1M sulphuric acid‚ H2SO4 1M acetic acid‚ HC2H3O2 1M phosphoric acid‚ H3PO4 Procedure: Please refer to Health Chemistry‚ Laboratory Experiments‚ page(s) 75-76. Data and Observations: Table 1: Comparison of Metal Activities Zinc Magnesium Copper Iron Hydrochloric acid Small bubbles Many bubbles N.R. color change (black)
Premium Sulfuric acid Zinc Hydrochloric acid
using HCl a strong acid to dissolve all the zinc inside the outer copper shell. The reaction follows as such; Zn+2HCLZnCl2+H2‚ but there will be no reaction with copper. The portion that will be measured is the mass of copper left after all of the Zn goes through the reaction process. Hypothesis: If the penny is post-1983‚ then there will be a percent yield of copper greater than 30%. Research Question: What is the percent composition of Copper and Zinc in a post-1983 penny? Aim: The purpose
Premium Copper Zinc Hydrochloric acid
reacts to oxygen and makes a rust proof film (zinc). When iron is coated in zinc it’s commonly known as galvanization. Galvanizing iron is one of the most commonly used techniques of preventing rust. The Zinc around the iron reacts faster and more with the oxygen in the environment then the iron does‚ thus creating a small film around the iron‚ blocking from contact with oxygen. The 4 metals that are being used in our experiment are common Steel‚ Zinc coated Iron (galvanized)‚ Copper‚ and Aluminium
Premium Iron Oxygen Metal
and Testing for Hydrogen Gas Felicity Tyler Aim: To produce and test for hydrogen gas. Materials: * rubber stopper * dilute hydrochloric acid (HCI) * zinc pieces (Zn) * test-tube rack * matches * dilute sulphuric acid (H2SO4) * 2 cm strips of magnesium ribbon (Mg) * Iron pieces (Fe) * Test-tube Method 1. Test the different metals with the acids by separately combining each
Premium Hydrochloric acid Sulfuric acid Hydrogen
Here is the summary of Great Wall Heavy Industry company professional engineers for everyone on methods of cone crusher wear parts replacement. 1.Methods of cone crusher wall replacement. Cone crusher wall and cone crusher body is fixed together with zinc alloy.Therefore‚for a new installation or replacement of a new cone crusher wall should check the tightening case to make sure to tighten reliable after working for 6-8 hours. 2.The gear meshing. Circular plate is worn due to process in the work of
Premium Zinc Tribology Wear
tin‚ 5% copper‚ 1% zinc – overcame expansion problems History • 1960’s – conventional low-copper lathe-cut alloys • smaller particles – first generation high-copper alloys • Dispersalloy (Caulk) – admixture of spherical Ag-Cu eutectic particles with conventional lathe-cut – eliminated gamma-2 phase Classification According to content – Silver amalgam: Silver more than 65% – Copper amalgam: 70% Hg and 30% Cu According to presence or absence of Zn Zinc containing alloys –
Premium Silver Zinc Copper
of brass‚ steel and solder and 2 other alloys of your choice‚ and explain how these uses relate to their properties. Brass: The two major metals in brass are copper and zinc. The proportion of the copper to zinc affects the colour of the alloy‚ ranging from a rose coloured alloy to a yellow alloy. The higher the proportion of zinc‚ the greater the hardness and tensile strength of the alloy. Brass can be highly polished and is lustrous which makes it useful for ornamental materials and musical instruments
Premium Zinc Iron Steel
Sulphate Solution 1mol.dm-3 Lead Nitrate Solution Zinc 25cm3 Measuring Cylinder Safety Goggles Balance Readings For this experiment the readings that you will need to take are the starting temperature of the solution being used and the maximum temperature that the solution reaches after zinc has been added. I have decided to use 25cm3 of each solution for the experiment this is 0.025mols of each therefore we need 0.025mols of zinc to react with it‚ 1 mol of Zn = 65g 65 x 0.025mols
Premium Thermodynamics Zinc Energy
LAB REPORT FOR EXPERIMENT 3 COPPER CYCLE OLANREWAJU OYINDAMOLA TUESDAY 27TH February 2013 Abstract This experiment is based on copper‚ to synthesize some copper compound using Copper (II) nitrate solution to obtain copper metal at the end. Changes of copper complexes when various are added and filtering out the precipitate by using Buchner funnel for vacuum filtration .The experiment started with preparation of copper (II) hydroxide and addition of copper oxide then addition of droplets
Premium Copper Zinc