Basic Electricity and Electronic Devices

Diodes
Diodes are components that allow current to flow in only one direction. They have a positive side (leg) and a negative side. When the voltage on the positive leg is higher than on the negative leg then current flows through the diode (the resistance is very low). When the voltage is lower on the positive leg than on the negative leg then the current does not flow (the resistance is very high). The negative leg of a diode is the one with the line closest to it. It is called the cathode. The postive end is called the anode.
LED
Light Emitting Diodes are great for projects because they provide visual entertainment. LEDs use a special material which emits light when current flows through it. Unlike light bulbs, LEDs never burn out unless their current limit is passed. A current of 0.02 Amps (20 mA) to 0.04 Amps (40 mA) is a good range for LEDs. They have a positive leg and a negative leg just like regular diodes. To find the positive side of an LED, look for a line in the metal inside the LED. It may be difficult to see the line. This line is closest to the positive side of the LED. Another way of finding the positive side is to find a flat spot on the edge of the LED. This flat spot is on the negative side.
When current is flowing through an LED the voltage on the positive leg is about 1.4 volts higher than the voltage on the negative side. Remember that there is no resistance to limit the current so a resistor must be used in series with the LED to avoid destroying it.
Resistors
Resistors are components that have a predetermined resistance. Resistance determines how much current will flow through a component. Resistors are used to control voltages and currents. A very high resistance allows very little current to flow. Air has very high resistance. Current almost never flows through air. (Sparks and lightning are brief displays of current flow through air. The light is created as the current burns parts of the air.) A low resistance allows a large amount of current to flow. Metals have very low resistance. That is why wires are made of metal. They allow current to flow from one point to another point without any resistance. Wires are usually covered with rubber or plastic. This keeps the wires from coming in contact with other wires and creating short circuits. High voltage power lines are covered with thick layers of plastic to make them safe, but they become very dangerous when the line breaks and the wire is exposed and is no longer separated from other things by insulation.
Resistance is given in units of ohms. (Ohms are named after Mho Ohms who played with electricity as a young boy in Germany.) Common resistor values are from 100 ohms to 100,000 ohms. Each resistor is marked with colored stripes to indicate it’s resistance. To learn how to calculate the value of a resistor by looking at the stripes on the resistor, go to Resistor Values which includes more information about resistors.

Variable Resistors
Variable resistors are also common components. They have a dial or a knob that allows you to change the resistance. This is very useful for many situations. Volume controls are variable resistors. When you change the volume you are changing the resistance which changes the current. Making the resistance higher will let less current flow so the volume goes down. Making the resistance lower will let more current flow so the volume goes up. The value of a variable resistor is given as it’s highest resistance value. For example, a 500 ohm variable resistor can have a resistance of anywhere between 0 ohms and 500 ohms. A variable resistor may also be called a potentiometer (pot for short). Switches
Switches are devices that create a short circuit or an open circuit depending on the position of the switch. For a light switch, ON means short circuit (current flows through the switch, lights light up and people dance.) When the switch is OFF, that means there is an open circuit (no current flows, lights go out and people settle down. This effect on people is used by some teachers to gain control of loud classes.)
When the switch is ON it looks and acts like a wire. When the switch is OFF there is no connection.
Using a Bread Board
To build our projects, we will use a breadboard like the one shown below. The bread board has many strips of metal (copper usually) which run underneath the board. The metal strips are laid out as shown below. These strips connect the holes on the top of the board. This makes it easy to connect components together to build circuits. To use the bread board, the legs of components are placed in the holes. The holes are made so that they will hold the component in place. Each hole is connected to one of the metal strips running underneath the hole.
Each strip forms a node. A node is a point in a circuit where two components are connected. Connections between different components are formed by putting their legs in a common node. On the bread board, a node is the row of holes that are connected by the strip of metal underneath.
The long top and bottom row of holes are usually used for power supply connections. The row with the blue strip beside it is used for the negative voltage (usually ground) and the row with the red strip beside it is used for the positive voltage.
The circuit is built by placing components and connecting them together with jumper wires. Then when a path is formed from the positive supply node to the negative supply node through wires and components, we can turn on the power and current flows through the path and the circuit comes alive.
A series connection of 2 resistors on a breadboard looks like the picture below on the left and a parallel connection of 2 resistors looks like the picture below on the right. For chips with many legs (ICs), place them in the middle of the board (across the middle dividing line) so that half of the legs are on one side of the middle line and half are on the other side.
A completed circuit might look like the following. This circuit uses two small breadboards.

1.6 Transistors and LEDs
Now we know enough that we can start to build circuits. But first we will look a little closer at a component that was introduced in Section 1.2.
The LED An LED is the device shown above. Besides red, they can also be yellow, green and blue. The letters LED stand for Light Emitting Diode. If you are unfamiliar with diodes, take a moment to review the components in Basic Components, Section 1.2. The important thing to remember about diodes (including LEDs) is that current can only flow in one direction.
To make an LED work, you need a voltage supply and a resistor. If you try to use an LED without a resistor, you will probably burn out the LED. The LED has very little resistance so large amounts of current will try to flow through it unless you limit the current with a resistor. If you try to use an LED without a power supply, you will be highly disappointed.
So first of all we will make our LED light up by setting up the circuit below. Step 1.) First you have to find the positive leg of the LED. The easiest way to do this is to look for the leg that is longer.
Step 2.) Once you know which side is positive, put the LED on your breadboard so the positive leg is in one row and the negative leg is in another row. (In the picture below the rows are vertical.)
Step 3.) Place one leg of a 2.2k ohm resistor (does not matter which leg) in the same row as the negative leg of the LED. Then place the other leg of the resistor in an empty row.
Step 4.) Unplug the power supply adapter from the power supply. Next, put the ground (black wire) end of the power supply adapter in the sideways row with the blue stripe beside it. Then put the positive (red wire) end of the power supply adapter in the sideways row with the red stripe beside it.
Step 5.) Use a short jumper wire (use red since it will be connected to the positive voltage) to go from the positive power row (the one with the red stripe beside it) to the positive leg of the LED (not in the same hole, but in the same row). Use another short jumper wire (use black) to go from the ground row to the resistor (the leg that is not connected to the LED). Refer to the picture below if necessary. The breadboard should look like the picture shown below. Now plug the power supply into the wall and then plug the other end into the power supply adapter and the LED should light up. Current is flowing from the positive leg of the LED through the LED to the negative leg. Try turning the LED around. It should not light up. No current can flow from the negative leg of the LED to the positive leg.
People often think that the resistor must come first in the path from positive to negative, to limit the amount of current flowing through the LED. But, the current is limited by the resistor no matter where the resistor is. Even when you first turn on the power, the current will be limited to a certain amount, and can be found using ohm’s law.
Revisiting Ohm's Law
Ohm's Law can be used with resistors to find the current flowing through a circuit. The law is I = VD/R (where I = current, VD = voltage across resistor, and R = resistance). For the circuit above we can only use Ohm's law for the resistor so we must use the fact that when the LED is on, there is a 1.4 voltage drop across it. This means that if the positive leg is connected to 12 volts, the negative leg will be at 10.6 volts. Now we know the voltage on both sides of the resistor and can use Ohm's law to calculate the current. The current is (10.6 - 0) / 2200 = 0.0048 Amperes = 4.8 mA
This is the current flowing through the path from 12V to GND. This means that 4.8 mA is flowing through the LED and the resistor. If we want to change the current flowing through the LED (changing the brightness) we can change the resistor. A smaller resistor will let more current flow and a larger resistor will let less current flow. Be careful when using smaller resistors because they will get hot.
Next, we want to be able to turn the LED on and off without changing the circuit. To do this we will learn to use another electronic component, the transistor.
1.6.1 The Transistor
Transistors are basic components in all of today's electronics. They are just simple switches that we can use to turn things on and off. Even though they are simple, they are the most important electrical component. For example, transistors are almost the only components used to build a Pentium processor. A single Pentium chip has about 3.5 million transistors. The ones in the Pentium are smaller than the ones we will use but they work the same way.
Transistors that we will use in projects look like this: The transistor has three legs, the Collector (C), Base (B), and Emitter (E). Sometimes they are labeled on the flat side of the transistor. Transistors always have one round side and one flat side. If the round side is facing you, the Collector leg is on the left, the Base leg is in the middle, and the Emitter leg is on the right.
Transistor Symbol
The following symbol is used in circuit drawings (schematics) to represent a transistor. Basic Circuit
The Base (B) is the On/Off switch for the transistor. If a current is flowing to the Base, there will be a path from the Collector (C) to the Emitter (E) where current can flow (The Switch is On.) If there is no current flowing to the Base, then no current can flow from the Collector to the Emitter. (The Switch is Off.)
Below is the basic circuit we will use for all of our transistors. To build this circuit we only need to add the transistor and another resistor to the circuit we built above for the LED. Unplug the power supply from the power supply adapter before making any changes on the breadboard. To put the transistor in the breadboard, seperate the legs slightly and place it on the breadboard so each leg is in a different row. The collector leg should be in the same row as the leg of the resistor that is connected to ground (with the black jumper wire). Next move the jumper wire going from ground to the 2.2k ohm resistor to the Emitter of the transistor.
Next place one leg of the 100k ohm resistor in the row with the Base of the transistor and the other leg in an empty row and your breadboard should look like the picture below. Now put one end of a yellow jumper wire in the positive row (beside the red line) and the other end in the row with the leg of the 100k ohm resistor (the end not connected to the Base). Reconnect the power supply and the transistor will come on and the LED will light up. Now move the one end of the yellow jumper wire from the positive row to the ground row (beside the blue line). As soon as you remove the yellow jumper wire from the positive power supply, there is no current flowing to the base. This makes the transistor turn off and current can not flow through the LED. As we will see later, there is very little current flowing through the 100k resistor. This is very important because it means we can control a large current in one part of the circuit (the current flowing through the LED) with only a small current from the input.
Back to Ohm's Law
We want to use Ohm's law to find the current in the path from the Input to the Base of the transistor and the current flowing through the LED. To do this we need to use two basic facts about the transistor.
1.) If the transistor is on, then the Base voltage is 0.6 volts higher than the Emitter voltage.
2.) If the transistor is on, the Collector voltage is 0.2 volts higher than the Emitter voltage.
So when the 100k resistor is connected to 12VDC, the circuit will look like this: So the current flowing through the 100k resistor is (12 - 0.6) / 100000 = 0.000114 A = 0.114 mA.
The current flowing through the 2.2k ohm resistor is (10.6 - 0.2) / 2200 = 0.0047 A = 4.7 mA.
If we want more current flowing through the LED, we can use a smaller resistor (instead of 2200) and we will get more current through the LED without changing the amount of current that comes from the Input line. This means we can control things that use a lot of power (like electric motors) with cheap, low power circuits. Soon you will learn how to use a microcontroller (a simple computer). Even though the microcontroller can not supply enough current to turn lights and motors on and off, the microcontroller can turn transistors on and off and the transistors can control lots of current for lights and motors.
For Ohm’s law, also remember that when the transistor is off, no current flows through the transistor.
1.6.2 Introduction to Digital Devices - The Inverter
In digital devices there are only two values, usually referred to as 0 and 1. 1 means there is a voltage (usually 5 volts) and 0 means the voltage is 0 volts.
An inverter (also called a NOT gate) is a basic digital device found in all modern electronics. So for an inverter, as the name suggests, it's output is the opposite of the input (Output is NOT the Input). If the input is 0 then the output is 1 and if the input is 1 then the output is 0. We can summarize the operation of this device in a table.

Input Output
1 0
0 1
To help us practice with transistors we will build an inverter. Actually we have already built an inverter. The transistor circuit we just built is an inverter circuit. To help see the inverter working, we will build a circuit with two inverters. The circuit we will use is shown below. First Inverter (already built) Second Inverter To build the circuit, use the transistor circuit we just built as the first inverter. The first inverter input is the end of the 100k ohm resistor connected to the yellow jumper wire. Build another circuit identical to the first (the basic transistor circuit from Section 1.6.1) except leave out the yellow jumper wire connected to the 100k ohm resistor (the inverter input). This circuit is the second inverter.
Connect the output of the first inverter to the input of the second inverter by putting one end of a jumper wire in the same row of holes as the 2.2k ohm resistor and the Collector of the transistor (the output of the first inverter) and putting the other end in the same row of holes as the leg of the 100k ohm resistor of the second inverter (the input to the second inverter).
Here is how to check if you built it correctly. Connect the first inverter input (the yellow jumper wire) to 12V (the positive row). The LED in the first inverter should come on and the LED in the second inverter should stay off. Then connect the first inverter input to 0V (the ground row). (You are turning off the switch of the first inverter.) The first LED should go off and the second LED should come on. If this does not happen, check to make sure no metal parts are touching. Check to make sure all the parts are connected correctly.
The input can either be connected to 12V or 0V. When the Inverter Input is 12V, the transistor in the first inverter will turn on and the LED will come on and the Inverter Output voltage will be 0.2V. The first Inverter Output is connected to the input of the second inverter. The 0.2V at the input of the second inverter is small enough that the second transistor is turned off. The circuit voltages are shown in the diagram below. When the Inverter Input is connected to 0V, the transistor in the first inverter is turned off and the LED will get very dim. There is a small amount of current still flowing through the LED to the second inverter. The voltage at the first Inverter Output will go up, forcing the second inverter transistor to come on. When the second inverter transistor comes on, the second inverter LED will come on. To find the voltage at the output of the first inverter (10.4V), use Ohm's law. There is no current flowing through the transistor in the first inverter so the path of the current is through the first LED, through the 2.2k resistor, through the 100k resistor, through the second transistor to ground. The voltage at the negative side of the first LED is fixed at 10.6V by the LED. The voltage at the second transistor base is fixed at 0.6V by the transistor. Then given those two voltages, you should be able to find the voltage at the point in the middle (10.4V) using Ohm’s law. (Hint: First find the current and then work through Form 1 of ohm’s law to find the voltage at the point between the 2.2k resistor and the 100k resistor.) Switch the input back and forth from 0V to 12V and you can see that when the first stage is on, the second stage is off. This demonstrates the inverting action of the Inverter.
1.7 Oscillators, Pulse Generators, Clocks... Capacitors and the 555 Timer IC Introduction
As electronic designs get bigger, it becomes difficult to build the complete circuit. So we will use prebuilt circuits that come in packages like the one shown above. This prebuilt circuit is called an IC. IC stands for Integrated Circuit. An IC has many transistors inside it that are connected together to form a circuit. Metal pins are connected to the circuit and the circuit is stuck into a piece of plastic or ceramic so that the metal pins are sticking out of the side. These pins allow you to connect other devices to the circuit inside. We can buy simple ICs that have several inverter circuits like the one we built in the LED and Transistor section or we can buy complex ICs like a Pentium Processor.
The Pulse - More than just an on/off switch
So far the circuits we have built have been stable, meaning that the output voltage stays the same. If you change the input voltage, the output voltage changes and once it changes it will stay at the same voltage level. The 555 integrated circuit (IC) is designed so that when the input changes, the output goes from 0 volts to Vcc (where Vcc is the voltage of the power supply). Then the output stays at Vcc for a certain length of time and then it goes back to 0 volts. This is a pulse. A graph of the output voltage is shown below.

The Oscillator (A Clock) - More than just a Pulse
The pulse is nice but it only happens one time. If you want something that does something interesting forever rather than just once, you need an oscillator. An oscillator puts out an endless series of pulses. The output constantly goes from 0 volts to Vcc and back to 0 volts again. Almost all digital circuits have some type of oscillator. This stream of output pulses is often called a clock. You can count the number of pulses to tell how much time has gone by. We will see how the 555 timer can be used to generate this clock. A graph of a clock signal is shown below.

1.7.1 The Capacitor
If you already understand capacitors you can skip this part.

The picture above on the left shows two typical capacitors. Capacitors usually have two legs. One leg is the positive leg and the other is the negative leg. The positive leg is the one that is longer. The picture on the right is the symbol used for capacitors in circuit drawings (schematics). When you put one in a circuit, you must make sure the positive leg and the negative leg go in the right place. Capacitors do not always have a positive leg and a negative leg. The smallest capacitors in this kit do not. It does not matter which way you put them in a circuit.
A capacitor is similar to a rechargable battery in the way it works. The difference is that a capacitor can only hold a small fraction of the energy that a battery can. (Except for really big capacitors like the ones found in old TVs. These can hold a lot of charge. Even if a TV has been disconnected from the wall for a long time, these capacitors can still make lots of sparks and hurt people.) As with a rechargable battery, it takes a while for the capacitor to charge. So if we have a 12 volt supply and start charging the capacitor, it will start with 0 volts and go from 0 volts to 12 volts. Below is a graph of the voltage in the capacitor while it is charging. The same idea is true when the capacitor is discharging. If the capacitor has been charged to 12 volts and then we connect both legs to ground, the capacitor will start discharging but it will take some time for the voltage to go to 0 volts. Below is a graph of what the voltage is in the capacitor while it is discharging.

We can control the speed of the capacitor's charging and discharging using resistors.
Capacitors are given values based on how much electricity they can store. Larger capacitors can store more energy and take more time to charge and discharge. The values are given in Farads but a Farad is a really large unit of measure for common capacitors. In this kit we have 2 33pf capacitors, 2 10uf capacitors and 2 220uF capacitors. Pf means picofarad and uf means microfarad. A picofarad is 0.000000000001 Farads. So the 33pf capacitor has a value of 33 picofarads or 0.000000000033 Farads. A microfarad is 0.000001 Farads. So the 10uf capacitor is 0.00001 Farads and the 220uF capacitor is 0.000220 Farads. If you do any calculations using the value of the capacitor you have to use the Farad value rather than the picofarad or microfarad value.
Capacitors are also rated by the maximum voltage they can take. This value is always written on the larger can shaped capacitors. For example, the 220uF capacitors in this kit have a maximum voltage rating of 25 volts. If you apply more than 25 volts to them they will die. We don’t have to worry about that with this kit because our power supply can only put out 12 volts.
1.7.2 The 555 Timer
Creating a Pulse
The 555 is made out of simple transistors that are about the same as on / off switches. They do not have any sense of time. When you apply a voltage they turn on and when you take away the voltage they turn off. So by itself, the 555 can not create a pulse. The way the pulse is created is by using some components in a circuit attached to the 555 (see the circuit below). This circuit is made of a capacitor and a resistor. We can flip a switch and start charging the capacitor. The resistor is used to control how fast the capacitor charges. The bigger the resistance, the longer it takes to charge the capacitor. The voltage in the capacitor can then be used as an input to another switch. Since the voltage starts at 0, nothing happens to the second switch. But eventually the capacitor will charge up to some point where the second switch comes on.
The way the 555 timer works is that when you flip the first switch, the Output pin goes to Vcc (the positive power supply voltage) and starts charging the capacitor. When the capacitor voltage gets to 2/3 Vcc (that is Vcc * 2/3) the second switch turns on which makes the output go to 0 volts.
The pinout for the 555 timer is shown below Deep Details
Pin 2 (Trigger) is the 'on' switch for the pulse. The line over the word Trigger tells us that the voltage levels are the opposite of what you would normally expect. To turn the switch on you apply 0 volts to pin 2. The technical term for this opposite behavior is 'Active Low'. It is common to see this 'Active Low' behavior for IC inputs because of the inverting nature of transistor circuits like we saw in the LED and Transistor Tutorial.
Pin 6 is the off switch for the pulse. We connect the positive side of the capacitor to this pin and the negative side of the capacitor to ground. When Pin 2 (Trigger) is at Vcc, the 555 holds Pin 7 at 0 volts (Note the inverted voltage). When Pin 2 goes to 0 volts, the 555 stops holding Pin 7 at 0 volts. Then the capacitor starts charging. The capacitor is charged through a resistor connected to Vcc. The current starts flowing into the capacitor, and the voltage in the capacitor starts to increase.
Pin 3 is the output (where the actual pulse comes out). The voltage on this pin starts at 0 volts. When 0 volts is applied to the trigger (Pin 2), the 555 puts out Vcc on Pin 3 and holds it at Vcc until Pin 6 reaches 2/3 of Vcc (that is Vcc * 2/3). Then the 555 pulls the voltage at Pin 3 to ground and you have created a pulse. (Again notice the inverting action.) The voltage on Pin 7 is also pulled to ground, connecting the capacitor to ground and discharging it.
Seeing the pulse
To see the pulse we will use an LED connected to the 555 output, Pin 3. When the output is 0 volts the LED will be off. When the output is Vcc the LED will be on.
Building the Circuit Place the 555 across the middle line of the breadboard so that 4 pins are on one side and 4 pins are on the other side. (You may need to bend the pins in a little so they will go in the holes.) Leave the power disconnected until you finish building the circuit. The diagram above shows how the pins on the 555 are numbered. You can find pin 1 by looking for the half circle in the end of the chip. Sometimes instead of a half circle, there will be a dot or shallow hole by pin 1.
Before you start building the circuit, use jumper wires to connect the red and blue power rows to the red and blue power rows on the other side of the board. Then you will be able to easily reach Vcc and Ground lines from both sides of the board. (If the wires are too short, use two wires joined together in a row of holes for the positive power (Vcc) and two wires joined together in a different row of holes for the ground.)
Connect Pin 1 to ground.
Connect Pin 8 to Vcc.
Connect Pin 4 to Vcc.
Connect the positive leg of the LED to a 330 ohm resistor and connect the negative end of the LED to ground. Connect the other leg of the 330 ohm resistor to the output, Pin 3.
Connect Pin 7 to Vcc with a 10k resistor (RA = 10K).
Connect Pin 7 to Pin 6 with a jumper wire.
Connect Pin 6 to the positive leg of the 220uF Capacitor (C = 220uF). (You will need to bend the positive (long leg) up and out some so that the negative leg can go in the breadboard.
Connect the negative leg of the capacitor to ground.
Connect a wire to Pin 2 to use as the trigger. Start with Pin 2 connected to Vcc.
Now connect the power. The LED will come on and stay on for about 2 seconds. Remove the wire connected to Pin 2 from Vcc. You should be able to trigger the 555 again by touching the wire connected to pin 2 with your finger or by connecting it to ground and removing it. (It should be about a 2 second pulse.)
Making it Oscillate
Next we will make the LED flash continually without having to trigger it. We will hook up the 555 so that it triggers itself. The way this works is that we add in a resistor between the capacitor and the discharge pin, Pin 7. Now, the capacitor will charge up (through RA and RB) and when it reaches 2/3 Vcc, Pin 3 and Pin 7 will go to ground. But the capacitor can not discharge immediately because of RB. It takes some time for the charge to drain through RB. The more resistance RB has, the longer it takes to discharge. The time it takes to discharge the capacitor will be the time the LED is off.
To trigger the 555 again, we connect Pin 6 to the trigger (Pin 2). As the capacitor is discharging, the voltage in the capacitor gets lower and lower. When it gets down to 1/3 Vcc this triggers Pin 2 causing Pin 3 to go to Vcc and the LED to come on. The 555 disconnects Pin 7 from ground, and the capacitor starts to charge up again through RA and RB. To build this circuit from the previous circuit, do the following.
Disconnect the power.
Take out the jumper wire between Pin 6 and Pin 7 and replace it with a 2.2k resistor (RB = 2.2K).
Use the jumper wire at pin 2 to connect Pin 2 to Pin 6.
Now reconnect the power and the LED should flash forever (as long as you pay your electricity bill).
Experiment with different resistor values of RA and RB to see how it changes the length of time that the LED flashes. (You are changing the amount of time that it takes for the Capacitor to charge and discharge.)
Formulas
These are the formulas we use for the 555 to control the length of the pulses. t1 = charge time (how long the LED is on) = 0.693 * (RA + RB) * C t2 = discharge time (how long the LED is off) = 0.693 * RB * C
T = period = t1 + t2 = 0.693 * (RA + 2*RB) * C
Frequency = 1 / T = 1.44 / ((RA + 2 * RB) * C) t1 and t2 are the time in seconds. C is the capacitor value in Farads. 220uF = 0.000220 F. So for our circuit we have: t1 = 0.693 * (10000 + 2200) * 0.000220 = 1.86 seconds t2 = 0.693 * 2200 * 0.000220 = 0.335 seconds
T = 1.86 + 0.335 = 2.195 seconds
Frequency = 0.456 (cycles per second)
Building a 5 Volt Power Supply
Most digital logic circuits and processors need a 5 volt power supply. To use these parts we need to build a regulated 5 volt source. Usually you start with an unregulated power supply ranging from 9 volts to 24 volts DC. To make a 5 volt power supply, we use a LM7805 voltage regulator IC (Integrated Circuit). The IC is shown below.

The LM7805 is simple to use. You simply connect the positive lead of your unregulated DC power supply (anything from 9VDC to 24VDC) to the Input pin, connect the negative lead to the Ground pin and then when you turn on the power, you get a 5 volt supply from the Output pin. This 5 volt output will be used as Vcc in the following projects.
Connect the red wire from the power supply adapter to the input of the 7805. Connect the black wire from the power supply adapter to the ground row (with the blue line beside it). Run a black jumper wire from the ground row to the ground of the 7805. Then use a yellow jumper to connect the 5 volt output to the row of holes with the red stripe beside it. The breadboarded circuit is shown below. Sometimes the input supply line (the 12VDC above) may be noisy. To help smooth out this noise and get a better 5 volt output, a capacitor is usually added to the circuit, going between the input and ground (GND). Find the 220 uF capacitor and put the long leg (positive leg) in the row of holes with the 12VDC line and put the short leg (negative leg) in ground (the row of holes next to the blue line).