B. Results and Discussion:
C. Experimental:
24 mL of 4-methylcyclohexanol, 5mL of phosphoric acid, and 1mL of concentrated sulfuric acid was added to a 250 mL round bottom flask and mixed thoroughly with a magnetic stirrer. A simple distillation set up was installed with a 250mL round bottom flask, jack, stirrer, heating mantle, and variac. The solution was heated gently with a small heating mantle to distill the crude product while keeping the vapor temperature around 100C or less. The crude product was collected which contained water, 4-methylcyclohexene, and trace acid.
D. Questions:
1. Outline a mechanism for the dehydration of 4-methylcyclohexanol catalyzed by phosphoric acid.
2. What major alkene product is produced by the dehydration of the following alcohols?
a. Cyclohexanol
Cyclohexene
b. 1-Methylcyclohexanol methylcyclohexene c. 2-Methylcyclohexanol methylcyclohexne d. 2,2-dimethylcyclohexanol
1,2-dimethylcyclohexene
3. Compare and interpret the infrared spectra of 4-Methylcyclohexene and 4-Methylcyclohexanol.
4. Identify the C-H out of plane bending vibrations in the infrared spectrum of 4-methylcyclohexne. What structural information can be obtained from these bands?
E. Literature Article:
Properties of 4-Methylcyclohexene
1. Flash point: 154F
2. OSHA recommended personnel exposure level (PEL): 50 ppm (235 mg/cu m)
3. DOT classification:
GUIDE 129: FLAMMABLE LIQUIDS (POLAR/WATER-MISCIBLE/NOXIOUS)/ Fire or Explosion: HIGHLY FLAMMABLE: Will be easily ignited by heat, sparks or flames. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than air. They will spread along ground and collect in low confined areas (sewers, basements, tanks). Vapor explosion hazard indoors, outdoors or in sewers. Those substances designated with "P" may polymerize explosively when heated or involved in a fire. Runoff to sewer may create
You May Also Find These Documents Helpful
-
To synthesize 4-methylcyclohexene from 4-methylcyclohexanol the starting material can be dehydrated resulting in the desired compound. For dehydration to be possible the OH group on the 4-methylcyclohexene must first be converted into H2O by means of an acid-base reaction using a strong acid catalyst such as phosphoric acid and sulfuric acid. The H2O will then become the favored leaving group and leave on its own resulting in the formation of a carbocation in excess water. The water will remove the acidic hydrogen on the carbocation producing the desired alkene as well as regenerating the acid catalyst (fig. 2). A time effective way to collect the 4-methylcyclohexene is to heat the reaction to reflux as it is taking place. This allows the product to be separated from the starting materials by means of the boiling point discrepancy between the isolated alkene (101-102C) and the starting alcohol (171-173C). After the distillate is collected any impurities of water and phosphoric acid can be extracted by adding sodium chloride, drying the resulting organic layer with an anhydrous solid, and filtration. IR of both the starting alcohol and the resulting alkene can be compared as a means of identification and characterization as well as a Br2…
- 757 Words
- 3 Pages
Satisfactory Essays -
Anhydrous sodium sulfate was added to the filtered organic solution to absorb excess water. Although water has a higher affinity towards sodium sulfate than cyclohexanol, excess anhydrous sodium sulfate may lead to the absorption of cyclohexane and thus loss of product. Anhydrous sodium sulfate absorbs water due to its polarity and therefore may also absorb cyclohexanol because of its polar O-H bond. If too much anhydrous sodium sulfate was added to the solution, part of the product would be absorbed too and thus a yield of less than 100% would be produced.…
- 455 Words
- 2 Pages
Good Essays -
About 1.55-g of benzil, 1.51-g of dibenzylketone and 12-mL of ethanol were placed in a 50-mL round bottom flask. A magnetic stir bar was also placed in the flask. A condenser was attached to the round bottom flask while the flask was placed in a 70oC hot water bath. The mixture was heated until all solids were dissolved. The temperature of the water bath was then heated to 80oC. A pasture pipet was used to add 2.25-mL of ethanolic potassium hydroxide solution downward through the condenser and into the flask.…
- 1204 Words
- 6 Pages
Best Essays -
7. Show how dehydration synthesis (condensation reaction) bonds occur at 2,3 and 5 prime carbons of sugar.…
- 877 Words
- 4 Pages
Good Essays -
Goggles were obtained and put on before entering the lab area. 2.0 grams of salicylic acid should be measured and placed into a 125 mL Erlenmeyer flask. 5.0 mL of acetic anhydride and 5 drops of 85% phosphoric acid was added to the Erlenmeyer flask. Drops of distilled water were added to rinse down bits of solids that were on inner wall of the flask. Mixture was heated on the hot plate for fifth-teen minutes, at 75 degrees Celsius. Two mL of distilled water was added 10 minutes into heating. Buchner funnel and filter were set up for the filtration…
- 1996 Words
- 8 Pages
Powerful Essays -
40ml of an equimolar mixture of cyclohexane and toluene was obtained and transferred into a 100ml round bottomed boiling flask which contained boiling chips. The distilling column was packed with metal sponge and the height was measured in centimeters and recorded. The distillation apparatus was assembled and a heat mantle was set. Several vials were used as fraction receivers. The vials were labeled, 1-4, and weighed prior to adding the liquid mixture and after the liquid was added. The temperature was recorded before adding heat in order to begin distillation (20º C). The temperature was recorded prior to each distillation fraction and after each 2ml of distillate which was recorded in table 1. The system was turned off and cooled down letting the remaining condensed vapor drain into the round bottomed flask. This sample was transferred by pipette into a vial…
- 729 Words
- 3 Pages
Good Essays -
Flammable: Any substance, liquid, solid, or the contents of a self-pressurized container, like aerosol cans, that can be easily set on fire or ignited. Extremely flammable, flammable, and combustible are the three types of flammability based on testing. Examples: Paint thinners, some solvents, adhesives, rubber cement, and hair…
- 463 Words
- 2 Pages
Good Essays -
In Experiment 9, distillation was used to carry out the dehydration of 2-methylcyclohexanol using 4:1 mixture of phosphoric and sulfuric acid. Gas Chromatography was then used to measure the products. Two products were formed. The theoretical yield of the alkene mixture was 3.914 g. The actual yield of the mixture was 0.73 g. The percent yield for the reaction was 18.65%. Peak A had an area of 0.3 mm2 and a percentage of 4.6 %. Peak B had an area of 6.21 mm2 and a percentage of 95.39%.…
- 1201 Words
- 5 Pages
Powerful Essays -
The Simple and Fractional distillation experiment was divided into two parts. We split up the procedure in this experiment. My group did the simple distillation and we received the Fractional distillation from another group in class. In this experiment, we examined the effectiveness of fractional and simple distillation to determine which is more successful at extracting a pure sample. This experiment was very successful. We are able to determine the success of the experiment but calculating refractive index of both types of distillation.…
- 274 Words
- 2 Pages
Good Essays -
As predicted from the Journal of Chemical Education articles, three methylcyclohexene products were observed. Their relative abundance measured by peak height was 80, 16, and 4%. The alkene products represented by these peaks apparently correspond to 1-methycyclehexene,…
- 1627 Words
- 7 Pages
Better Essays -
In the first step, the mixture of water, concentrated sulphuric acid, and cyclohexene was shaken vigorously until it became a homogenous solution. Followed by, the addition of water, and the distillation process lead to the hydrolysis of the alkene. Finally, addition of diethyl ether to the mixture then distillation took place to be purified and to obtain the final product, cyclohexanol (McFadden, 2012). Diethyl ether was used to extract alcohol from salt-water mixture because diethyl ethers solubility in water is lower than cyclohexanol which helps remove alcohol from the salt-water mixture (Merzougui, A, et al., 2011).…
- 2173 Words
- 9 Pages
Better Essays -
We are going to investigate the functional group’s bond type and strength by 3 different method, resonance theory, Spartan 3D modeling program, and the IR spectrophotometer. By resonance theory, we are going to draw out Lewis structure for each compound, then based on the numbers of the resonance we are able to create to determine the bond strength for each functional group. As for second method, we are using the Spartan modeling software, where we are able to draw out each of the functional group and have the software calculate the theoretical bond strength for us. And lastly, the IR spectroscopy are used is this experiment to measure the bond strength of each compound, and all the significant data are being collected in our lab notebook in order to further compare with theoretical bond strength. IR spectrophotometer reads off the amount of electromagnetic spectrum being absorbed by the compound then project the frequency IR graph on the computer.…
- 547 Words
- 4 Pages
Satisfactory Essays -
A broad absorption band appeared in the IR spectrum, (fig.2.3) at 3484.74cm-1 was due to the presence of the hydroxyl group. A sharp absorption band appeared at 1680.24cm-1 shows the presence of a ketoneic group. While peaks appeared in 1604 and 1053cm-1 shows the presence of aromatic C=C unsaturation and the ether groups respectively.…
- 209 Words
- 1 Page
Good Essays -
The first three labs of this organic chemistry experiment involved carrying out the first three parts of the Cyclohexanol Cycle. The cyclohexanol was first converted to cyclohexene and water by simple distillation (product: 6.5395g, 79.75% recovery). The cyclohexene then underwent a bromination reaction by addition of concentrated HBr and a 30% H2O2 solution, followed by an extraction of the aqueous phase. This produced trans-1,2-dibromocyclohexane (product: 12.8886g, 67.34% recovery). The trans-1,2-dibromocyclohexane was reduced by zinc metal to cyclohexene. The reaction was conducted in water, first allowing the reaction to reflux and then isolating the cyclohexene by distillation (product: 4.2144g, 95.89%).…
- 1293 Words
- 6 Pages
Good Essays -
Distillation is a technique used to purify various liquids. In a simple distillation, a liquid is boiled and the vapors work through the apparatus until they reach the condenser where they are cooled and reliquified. Liquids are separated based upon their differences in boiling point in which each pure substance is at least greater than 40-50 °C. A liquid has a specific boiling temperature at standard pressure conditions. If there are two liquids in a solution, the liquid with the lowest boiling point can be boiled out of the solution without removing a significant amount of the other liquid. By vaporizing the liquid and condensing it in another container, one can obtain a pure sample of the liquid. Any impurities and liquids with higher boiling points remain in the original container.…
- 361 Words
- 2 Pages
Satisfactory Essays