Preview

Explain How It Is Used To Equalize The Force Of Unbalanced Force

Good Essays
Open Document
Open Document
537 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Explain How It Is Used To Equalize The Force Of Unbalanced Force
Background This experiment was used to test if a force with the same magnitude at opposite angles would equal to a net force of zero. If we equalize all the forces so we get a net gain force of 0 then no weight should touch the floor or the pulleys. We then tested if we added an extra weight with certain angle. We found out at what angle and what weight would equalize the force. The dependent variable is the force we used to equalize the force table. The controlled variables are the weight we initialized to create an unbalanced force.

Equipment

We used all the tools that were specified in the laboratory.

Procedure

Make sure the force table is balanced on the table.
Adjust all the ropes so that the weights will not touch the table.
…show more content…
We incremented the weight slowly until the two weights were balanced.
We than placed the two other weights at the angled specified making sure the pulleys would be able to spin.
We started by pulling the rope in the opposite direction to find where the weight would equalize the angle.
We incremented the weights on the mass hanger by increments until the middle ring centered and all the masses were lifted off the table..
We repeated steps 6 and 7 with three weights instead of 2.
For the problem about moving a car by tying a rope to a tree to a car and adding a force perpendicular to the rope
We started by making a scale by representing the car as 200g and to move a the weight 1 micrometers.
We put a the biggest weight we had as the tree at 180 degrees and the car at 0 with a weight of 200g.
Next we put the pulley at 90 which is our perpendicular force.
As we put weight the perpendicular force we measured how far did the weight move using a ruler. Until it moves one 1 micrometer.

You May Also Find These Documents Helpful

  • Good Essays

    Plug the force sensor into channel 1 of your LabQuest 2, this allows you to calculate the amount of force that you pull the block with.…

    • 471 Words
    • 2 Pages
    Good Essays
  • Good Essays

    blach

    • 495 Words
    • 2 Pages

    1. We pulled the block slowly and consistently in order to obtain an accurate and representative measurement. We also pulled at a constant velocity with an acceleration of zero, so the net force of the movement would be zero as well (Fnet=mass x acceleration). Had we pulled the block at a non-uniform velocity, the force required to move the block would have been inconsistent.…

    • 495 Words
    • 2 Pages
    Good Essays
  • Satisfactory Essays

    AP Physics Slinky Lab

    • 468 Words
    • 4 Pages

    1. The first slinky’s mass was weighed, using a scale, and its tension was measured using a…

    • 468 Words
    • 4 Pages
    Satisfactory Essays
  • Satisfactory Essays

    1. Determine the magnitude of the reactions on the beam at A and B in Fig. 1. Neglect the thickness of the beam. (5-11). 2. Determine the tension in the cable and the horizontal and vertical components of reaction of the pin A in Fig. 2. The pulley at D is frictionless and the cylinder weighs 80 lb. (5-18)…

    • 262 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    Adulterated Herb Lab

    • 516 Words
    • 3 Pages

    The purpose of this lab is to analyze the volatile oils of some herbs through TLC testing and then identify the adulterant in a sample.…

    • 516 Words
    • 3 Pages
    Satisfactory Essays
  • Powerful Essays

    Physic Lab

    • 1399 Words
    • 6 Pages

    4. Repeat the procedure with an increased net force. For example, you can transfer one of the 100-g masses from the cart to the string hanging over the pulley. This allows the mass of the system to remain constant. Determine the data for α2.…

    • 1399 Words
    • 6 Pages
    Powerful Essays
  • Good Essays

    Trigonometry Lab Report

    • 583 Words
    • 3 Pages

    To start the experiment, weigh the mass of the cart with the picket fence and record the mass on an excel worksheet. The combined weight of the cart and the picket fence will be referred to as M. After weighing the cart with the picket fence, assemble the dynamic track by installing the photogate at an appropriate position. Additionally, install the pulley at the applicable end of the dynamic track. Next, hook up the inextensible string to the end of the cart. The attached string should be facing the photogate and the pulley. After attaching one end of the string to the cart, attach the hanging mass to the other end of the string. The hanging mass without any slotted masses should have a weight of 50 grams. The mass of the hanging mass will…

    • 583 Words
    • 3 Pages
    Good Essays
  • Satisfactory Essays

    In the beginning the United States wasn’t even united. We were just states. We broke away from that powerhouse called Great Britain by having a revolution which was the American Revolution. After this revolution had taken place with many bloody battles on American soil and caused the casualties of many British and Americans alike. After the bloody warfare the Americans came out on top and can officially declare their independence from Britain.…

    • 548 Words
    • 3 Pages
    Satisfactory Essays
  • Powerful Essays

    Wooden Block Lab

    • 865 Words
    • 4 Pages

    After that, we made sure there was enough room for the hanger to fall freely before hanging the thread over the pulley. Next, we varied the hanger height while maintaining the same mass. We measured the height at which the hanger dropped and the mass of the block and hanger. We recorded the block movement in films from various heights. Before moving on to the other videos, we examined the first one to guarantee accurate results.…

    • 865 Words
    • 4 Pages
    Powerful Essays
  • Satisfactory Essays

    Live Life

    • 330 Words
    • 2 Pages

    3. Place the lass on the table at the starting point. Hold the force meter parallel to the tabletop. Pull the mass at a constant speed along the surface of the table to the 0.50 m mark. Observe the force measured on the force meter…

    • 330 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    2. Placed 900g of weight on the cart and 100g of weight hanged from the string…

    • 1283 Words
    • 6 Pages
    Good Essays
  • Satisfactory Essays

    1. Why were pulleys used in the experiment? Why were the strings not simply run over the edge of the force table?…

    • 542 Words
    • 3 Pages
    Satisfactory Essays
  • Good Essays

    Lab 5: Weightlifting

    • 622 Words
    • 3 Pages

    We then drew a force diagram for the force acting on the barbell and when the lifter held the…

    • 622 Words
    • 3 Pages
    Good Essays
  • Satisfactory Essays

    Slavery created a lot of struggles for slaves in the American South. Slaves in the American South had hard working conditions. And had families. Split up from them.…

    • 189 Words
    • 1 Page
    Satisfactory Essays
  • Good Essays

    Weighty Matter Lab Report

    • 572 Words
    • 3 Pages

    Repeat the first two trials until 7 trials have been performed and recorded. When using the weights, be sure to not exceed .45kg in any trial. 4.) When all the masses are recorded with their corresponding spring forces, calculate the weight force, Fg, and record. 5.)…

    • 572 Words
    • 3 Pages
    Good Essays