Preview

Heat Exchanger

Good Essays
Open Document
Open Document
542 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Heat Exchanger
Heat exchanger
A heat exchanger is a device that is used to transfer thermal energy (enthalpy) between two or more fluids, between a solid surface and a fluid, or between solid particulates and a fluid, at different temperatures and in thermal contact. In heat exchangers, there are usually no external heat and work interactions. Typical applications involve heating or cooling of a fluid stream of concern and evaporation or condensation of single- or multicomponent fluid streams. In a few heat exchangers, the fluids exchanging heat are in direct contact. In most heat exchangers, heat transfer between fluids takes place through a separating wall or into and out of a wall in a transient manner. In many heat exchangers,the fluids are separated by a heat transfer surface, and ideally they do not mix or leak. Such exchangers are referred to as direct transfer type, or simply recuperators. In contrast, exchangers in which there is intermittent heat exchange between the hot and cold fluids—via thermal energy storage and release through the exchanger surface or matrix—are referred to as indirect transfer type, or simply regenerators. Such exchangers usually have fluid leakage from one fluid stream to the other, due to pressure differences and matrix rotation/valve switching.
Common examples of heat exchangers are shell-and tube exchangers, automobile radiators, condensers, evaporators, air preheaters, and cooling towers. If no phase change occurs in any of the fluids in the exchanger, it is sometimes referred to as a sensible heat exchanger. Heat transfer in the separating wall of a recuperator generally takes place by conduction. However, in a heat pipe heat exchanger, the heat pipe not only acts as a separating wall, but also facilitates the transfer of heat by condensation, evaporation, and conduction of the working fluid inside the heat pipe. In general, if the fluids are immiscible, the separating wall may be eliminated, and the interface between the fluids replaces

You May Also Find These Documents Helpful

  • Better Essays

    ESWBR final

    • 1191 Words
    • 4 Pages

    Normally used for power operations, the reactor coolant pumps can be also used for decay heat removal at slower speeds or different coolant pump combinations. In an intensive emergency situation where coolant exits the system, known as a Loss of Coolant Accident (LOCA), emergency measures must be enacted to provide a source of makeup water to the core to provide adequate cooling. This emergency cooling is provided for by the ECCS which is comprised of four subsystems; the Gravity Driven Cooling System (GDCS), Isolation Condenser System (ICS), Standby Liquid Cooling System (SLCS), and the Automatic Depressurization System (ADS). The later is technically a part of the Nuclear Boiling System (NBS).…

    • 1191 Words
    • 4 Pages
    Better Essays
  • Satisfactory Essays

    In my view the two most important heat transport processes are convection and conduction that are taking place when blowing into a hot bowl of soap.…

    • 346 Words
    • 2 Pages
    Satisfactory Essays
  • Better Essays

    3. Liu, Hongtan. Heat Exchangers: Selection, Rating, and Thermal Design. 2nd ed. Boca Raton: CRC, 2000. Print.…

    • 1284 Words
    • 9 Pages
    Better Essays
  • Powerful Essays

    Refrigeration & AC Thermal energy moves from left to right through five loops of heat transfer: 1) 2) 3) 4) 5) Indoor air loop Chilled water loop Refrigerant loop Condenser water loop Cooling water loop 4 Introduction AC Systems Refrigeration & AC AC options / combinations: • Air Conditioning (for comfort / machine) • Split air conditioners • Fan coil units in a larger system • Air handling units in a larger system 5 Introduction Refrigeration & AC Refrigeration systems for industrial processes • Small capacity modular units of direct expansion type (50 Tons of Refrigeration) • Centralized chilled water plants with chilled water as a secondary coolant (50 – 250 TR) • Brine plants with brines as lower temperature, secondary coolant (>250 TR) 6 Introduction Refrigeration at large companies Refrigeration & AC…

    • 1908 Words
    • 32 Pages
    Powerful Essays
  • Good Essays

    Title Title Titile

    • 273 Words
    • 2 Pages

    - The work input transfers heat form a low- temperature reservoir to a high temperature reservoir…

    • 273 Words
    • 2 Pages
    Good Essays
  • Satisfactory Essays

    Heat Transfer

    • 418 Words
    • 2 Pages

    i) Calculate the heat loss from the vertical surface of the receiver due to convection. Assume effects of curvature are negligible.…

    • 418 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    Heat exchanger: The heat exchanger is the part of your furnace that heats the air that fills your home, so it is very important that it is working when you need to use your furnace. What many people have noticed is…

    • 500 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    Sequence of Operation

    • 354 Words
    • 2 Pages

    4. The heat exchanger is heated until a device tells the blower to come on, usually a fan and limit control.…

    • 354 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    Thermal Equilibrium

    • 2551 Words
    • 11 Pages

    Fig. 1.01 shows two systems A and B separated by an adiabatic wall (a wall which does not allow hear flow).The two systems are placed in contact with a third system C with a diathermic wall (a wall which permits heat flow) in between.…

    • 2551 Words
    • 11 Pages
    Good Essays
  • Satisfactory Essays

    process equipment design

    • 569 Words
    • 3 Pages

    Crude oil at the rate of 150,000 kg/h is to be heated from 20 to 570 C by heat exchange with the bottom product from a distillation unit. The product at 129,000 kg/h is to be cooled from 146 to 1070 C. There is available a tubular exchanger with steel tubes with an inside shell diameter of 23 1/4 in., having one pass on the shell side and two passes on the tube side. It has 324 tubes, ¾ in. OD, BWG 14, 12 ft long arranged on a 1-in. square pitch and supported by baffles with a 25% cut, spaced at 9-in. intervals. Would…

    • 569 Words
    • 3 Pages
    Satisfactory Essays
  • Good Essays

    Because freshwater generators often use existing heat to run, the cost of operation is low. A water cooling system is divided into two separate systems: one for cooling the cylinder jackets, cylinder heads and turbo-blowers; the other for piston cooling. Jacket Cooling System…

    • 704 Words
    • 4 Pages
    Good Essays
  • Good Essays

    CHE 391

    • 1070 Words
    • 5 Pages

    Hot water is heated in a reservoir through heating coils and pumped through a magnet…

    • 1070 Words
    • 5 Pages
    Good Essays
  • Satisfactory Essays

    Heat Pump

    • 313 Words
    • 2 Pages

    Tabulate your results in the following table. Calculate the coefficient of performance and compared with the ideal coefficient of performance.…

    • 313 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    Water

    • 265 Words
    • 2 Pages

    4. Hot and Cold Dispenser, the dispenser can be used to heat water and cool water. If you want to heat water, dispenser uses the working principle of the heating element (heater). If you want to cool the water dispenser uses the principle of element cooling (fan or refrigan).…

    • 265 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    A heat transformer is a device that transfers a part of the heat, supplied to it…

    • 20268 Words
    • 82 Pages
    Powerful Essays

Related Topics