Purpose: To observe the characteristic colors produced when certain metallic ions are vaporized. Metallic Ion Color in Flame Na+ Light Orange K+ Pink / Orange Li Red Ca2+ Dark Orange Sr2+ Red Cu2 Green Co+2 Salmon Pink Ammonium Dichlorate Orange Sparks K2CR2O7 Orange Fe+1 No Reaction NaCl Orange Strantium Chloride Scarlet Red Ni+2 Dark Orange Copper Sulfate (solid) Green Fe+2
Premium Photon Atom Electromagnetic radiation
were some patterns that were noticeable during this experiment. It was noticed that all of the sprays with the metal potassium in them had turned the flame a light pink for a few seconds. The sprays that held the copper in them all turned the flame a vivid green colour‚ with some including green sparks also. Both of the sodium bottles turned the flame orange for a short time. Electrons orbit the nucleus of an atom in energy levels. If atoms are heated up to the point where the electrons are orbiting
Premium Fundamental physics concepts Light Atom
Flame lab test Chemistry Introduction The lab test performed was to determine characteristic colors that were produced by specific metallic ions that are shown in a flame. This happens when an electron gains energy; the electron moves from an energy level that’s farthest away and to an empty orbital close to the nucleus with higher levels‚ so one of the electrons gives off energy. A flame test is a visual test where the energy is in the form of a color change and the change can
Premium Atom Metal Potassium
Background In the Flame test lab we took a simple wire‚ looped it‚ and rinsed it in HCL (Hydrochloric Acid ). Then we dipped the wire in the different samples provided. The samples provided were Sodium‚Potassium‚Calcium‚ Barium‚ Strontium‚ Lithium ‚ and Copper II. Finally we put the wire loop into the flame of the bunsen burner. The flame erupted into many different colors for each specific sample. We then used the colors we recorded to find the two unknown samples given to us. But the question
Premium Oxygen Light Chemistry
Flame test: AIM: To determine which part of the salt is responsible for the characteristics in the flame. HYPOTHESIS: If we introduce a metal salt in the blue flame of the Bunsen burner‚ then the colour given off by the flame is due to the metal part of the salt. METHOD: (1) With a heat proof mat under the Bunsen burner‚ turn the gas on and light up the Bunsen burner with matches. (2) Pour enough Hydrochloric acid into a beaker. (3) Using your wire‚ dip it into the beaker containing Hydrochloric
Premium Sodium chloride Salt Potassium
A flame test is conducted when an element is burned and the flame produces a color different the starting flame color. When the coffee stirrer was put into the flame‚ the element’s atoms (from the solution of the stirrer) left the original level of energy. When the atoms fell back to ground level‚ they released photons in the form of colored flame. Using the flame test‚ unknown compounds can be identified when they are burned since each element has a specific color. (Douma‚ 2008). The color
Premium Potassium Color Emission spectrum
this‚ rinse it with distilled water from the wash bottle‚ dip it into the Hydrochloric Acid‚ and place it in the burner flame for a few moments. 4. Take note of the color of the flame when the wire is clean. This is the color you should see after each cleaning. 5. Once the wire is clean‚ dip it into one of the solutions‚ place the wire in the flame‚ and observe the color of the flame. 6. Clean the Nichrome wire as directed in step 3‚ then repeat step 5 until all of the solutions have been tested.
Premium Metal Ammonia Potassium
Lab Questions: Are flame tests valuable for detecting metal ions present in a mixture of metal ions? Flame test may not be valuable for detecting individual metal ions present in a mixture of metal ions. Although each metal ion emits a different color of light‚ which corresponds to a certain wavelength of light‚ the presence of some elements may over power the flame and cause only certain wavelengths to be seen. For example‚ if sodium
Premium Electron Light Quantum mechanics
chemistry lab report : reaction of alcohol CHEMISTRY LAB REPORT SK026 SEMESTER 2 SESSION 2011/2012 TITLE :REACTION OF ALCOHOL DATE : NAME : MATRIC NO : PARTNER : PRACTICUM : SUPERVISOR : Title : Reaction Of Alcohol Objectives : 1. To classify alcohol 2. To study the chemical properties of alcohols Introduction: Alcohol is a class of organic compound containing hydroxyl group‚ OH as the
Premium Alcohol Ethanol Carboxylic acid
Kevin Nam Honors Chemistry 3/22/14 Mr. Mihordea Motion of Atoms and Molecules lab summary In this lab the standard heat of combustion of magnesium was calculated by using the calorimeter. Also‚ the point of combustion of magnesium was to see how much heat would be released from fireworks such as sparklers. The concept of this lab was to find the difference in temperature
Premium Thermodynamics Hydrogen Heat