Chemistry Lab Report 1 Nicole H. Healey (Experiment 1 and 2) October 7‚ 2014 Data Collection: Table 1: (First Titration) C2O42- Analysis Sample 1 Sample 2 Molarity of KMnO4 0.02m 0.02m Weight of Sample 0.237g 0.225g Final Buret Reading 28.5ml 26.3ml Initial Buret Reading 0ml 0ml Volume of KMnO4 dispensed 28.5ml 26.3ml Moles
Free Titration Potassium permanganate Mole
9/19/2012 Experiment #1-Density Aim: Learn how the process of distillation occurs. Observe how distillation separates alcohol from wine. Method: Distillation is based on the fact that the matter can exist in three phases - - solid‚ liquid and gas. As the temperature of a pure substance is increased‚ it passes through these phases‚ making a transition at a specific temperature from solid to liquid (melting point--mp) and then at a higher temperature from liquid to gas (boiling point--bp). Distillation
Premium Distillation Water Evaporation
INTRODUCTION: The purpose of this experiment is to measure the formation constant of the tetraamminecopper(II) ion by colorimetry. Anhydrous copper sulfate (CuSO4) is white‚ which means that it does not absorb light in the visible region of the spectrum. The hydrated copper sulfate (CuSO4 - 5H2O) is blue. The structure of the compound can be represented more accurately as Cu(H2O)4 SO4 - H2O where four water molecules are bound to the copper ion and the fifth is a water of crystallization. The
Premium Ammonia Chemistry Copper
In this lab‚ the pH of flat sprite and a fresh sprite are compared two ways: one way was to record the pH directly with a digital pH probe and the other was to calculate the concentration through titration. Because the reaction is a neutralization reaction‚ the concentration of can be calculated if the concentration of is known. At the end of the titration‚ the moles of will equal the moles of and the pH is expected to be greater than 7 because the found in sprite is weak and is a strong
Premium Acid PH Acid dissociation constant
Chemistry design: Fuel energy lab Research question: What is the energy density of cyclohexane‚ and how does it compare to the energy density of normal hexane? Variables: Independent variable – The independent variable in this experiment will be the type of fuel that will be used. This will be either Hexane or Cyclohexane. Each type will be given to us and labelled so it will be quite simple to control this variable. This cannot be measured using any apparatus so the lab assistant must be entrusted
Premium Heat Temperature Energy
Chemistry 11 Final Examination Review - Answers Part A - True or False. Indicate whether each of the following statements is true or false. Correct the false statements. F 1. The mass of an electron is equal to the mass of a proton. The mass of an electron is less than the mass of a proton. T 2. The mass of a proton is approximately equal to the mass of a neutron. T 3. The atomic number represents the number of protons in a nucleus. T 4. The proton has a mass of approximately
Premium Atom Sulfuric acid Oxygen
IB1 Chemistry Practical #8 ANALYSIS OF ASPIRIN TABLETS For a long time the bark of the willow tree (salix alba) was used as a traditional medicine to relieve the fever symptoms of malaria. In the 1860’s chemists showed that the active ingredient in willow bark is salicylic acid (2-hydroxybenzoic acid) and by 1870 salicylic acid was in wide use as a pain killer (analgesic) and fever depressant (antipyretic). However‚ because it is a relatively strong acid‚ salicylic acid has the undesirable side effect
Premium Aspirin Sodium hydroxide Salicylic acid
Experiment #5: Acid Burn!!! Introduction The goal of this lab was to correctly prepare a 0.2M solution of NaOH‚ identify highly acidic household cleaning chemicals‚ and determine their concentration (molarity) through titrations using the previously prepared 0.2M NaOH solution. Experimental First‚ to create 0.5L of 0.2M solution of NaOH‚ standard 3M NaOH solution was obtained. Next‚ calculations were performed to determine the amount 3M NaOH necessary to create 0.5L of the 0.2M solution and‚ as
Premium Chemistry Sodium hydroxide Base
Lehman‚ John. Operational Organic Chemistry‚ 3rd Edition. Experiment 4 (pp. 38-45; 680-687; 644-650)‚ Prentice-Hall‚ 1999. 2.) Laboratory Reference Manual: Experiment 3. Retrieved from: http://academic.reed.edu/chemistry/alan/201_202/lab_manual/expt_salicylic_acid/background.html 3.) Lab 5: Synthesis of Salicylic Acid. Retrieved from: http://academic.evergreen.edu/curricular/whatscookin/Lab%20five%20%20methyl%20saliclate.htm 4.) Handout: Synthesis of Salicylic Acid. Retrieved from: g.web.umkc.edu/gounevt/Orgo320L/Handouts/SalicylicacidW04
Premium Chemistry Oxygen Organic chemistry
Figure 2 Figure 3 Figure 1 show the crystallisation reaction when the saturated sodium chloride solution was added to the cool reaction mixture. The salt of p-Toluenesulphonic acid started forming. Figure 2 show the wet crystal after the precipitated salt was being filtered by suction. The wet crystal was light purple in colour. Figure 3 show the end product after drying the wet crystal at 105°C in the drying cabinet (oven)
Premium Chemistry Water Acetic acid